manualshive.com logo in svg

Hino 238, Руководство по ремонту

Tascam 238 - многодорожечный кассетный записывающий аппарат с возможностью записи восемью дорожек. Для более подробной информации обращайтесь к руководству пользователя. Скачать бесплатно владельческое руководство можно на manualshive.com. Начните использование сегодня и наслаждайтесь качеством звука!

Поделиться
Скачать
background image

ENGINE CONTROL SYSTEM (J08E)

4–886

1.

Set the starter switch to the "LOCK" position.

2.

Disconnect the EGR valve connector.

3.

Set the starter switch to the "ON" position.

4.

Use the electrical tester to measure the voltage between the termi-
nals of the EGR valve vehicle-side connector.

NO

YES

1.

Set the starter switch to the "ON" position.

2.

Select [Engine] and check if the DTC (P14BC or P14BD) has been
detected in [Fault Information].

NO

YES

3

Inspect the EGR valve power supply

EGRV

EGRG

SAPH16F010300700

Measurement

conditions

Tester connections

Standard values

Starter switch: ON

EGR valve vehicle-
side connector
EGRV 

–

 EGRG

8 

–

 16 V

Do the measurements meet the standard value?

Replace the EGR valve, go to step 4.

Check the wire harness (actuator power sup-
ply and ground) and battery voltage. Repair
or replace parts as needed.
Perform "After-inspection work" of INFOR-
MATION section.

4

Check the DTC detected 2 (Engine ECU) [Hino-DX]

Select

Engine

SAPH16F010300701

Has DTC (P14BC or P14BD) been detected?

Replace the engine ECU.
Perform "After-inspection work" of INFOR-
MATION section.

Procedure completed.
Perform "After-inspection work" of INFOR-
MATION section.

Содержание 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 238

TATA Motors Safari Owner'S Manual & Service Book preview
Safari
Бренд: TATA Motors Страницы: 161
TAUBENREUTHER 16 - 590 Fitting Instructions Manual preview
16 - 590
Бренд: TAUBENREUTHER Страницы: 11
Yakima SKYBOX Series Manual preview
SKYBOX Series
Бренд: Yakima Страницы: 15
Warrior Winches C10000NH Assembly & Operating Instructions preview
C10000NH
Бренд: Warrior Winches Страницы: 17
Front Runner Easy-Out Fitting Instructions preview
Easy-Out
Бренд: Front Runner Страницы: 5
GMC ANDROID INTERFACE Instruction Manual preview
ANDROID INTERFACE
Бренд: GMC Страницы: 18
Prorack K496 Fitting Instructions For Basic Carrier preview
K496
Бренд: Prorack Страницы: 15
Whispbar K934W Fitting Instructions Manual preview
K934W
Бренд: Whispbar Страницы: 15
Cadillac 1999 DeVille Owner'S Manual preview
1999 DeVille
Бренд: Cadillac Страницы: 368
Luverne 205760 Installation Instructions preview
205760
Бренд: Luverne Страницы: 3
Navman B2+ User Manual preview
B2+
Бренд: Navman Страницы: 27
Fab Fours F2950 Installation Instructions Manual preview
F2950
Бренд: Fab Fours Страницы: 21
Weltmann KFZ-Teile 9B500016 Fitting Instructions Manual preview
9B500016
Бренд: Weltmann KFZ-Teile Страницы: 12
Dodge 2010 Challenger SRT Owner'S Manual preview
2010 Challenger SRT
Бренд: Dodge Страницы: 444
BMW M3 SEDAN Owner'S Manual preview
M3 SEDAN
Бренд: BMW Страницы: 392
Curt Manufacturing 13434 Installation Instructions preview
13434
Бренд: Curt Manufacturing Страницы: 4
Jeep CHEROKEE 2017 User Manual preview
CHEROKEE 2017
Бренд: Jeep Страницы: 374
Thule 145012 Quick Start Manual preview
145012
Бренд: Thule Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды