Harsen GU641B Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 60

background image

Manual

HM1016ER1

Parameters Setting

Harsen

®

Page 34/54

Coolant Alarm:

Used to configure the high engine temperature alarm value for the engine.

The signal is derived form HET sensor, this function would be inactive if do not use HET sensor.

When parameter is set as “9999”, this function is inactive.

Batt. Undervolt:

Used to configure the low battery voltage pre-alarm.

When parameter is set as “0”, this function is inactive.

Batt. overvolt:

Used to configure the high battery voltage pre-alarm.

When parameter is set as “99.9”, this function is inactive.

Alt. low preALM:

Used to configure the low charger voltage value.

Voltage signal is derived from the excitation winding of charger.

When parameter is set as “0”, this function is inactive.

EX. Crank permit:

Used to configure the permit of external crank.

Refer to 4.8 for details.

«
...
37
38
39
40
41
...
»

Содержание GU641B





























































Отзывы:

Нет отзывов

Похожие инструкции для GU641B

Concord express

Бренд: GE Страницы: 3

Бренд: Quinny Страницы: 29

Бренд: Quinny Страницы: 60

Compact Comfort VAV12

Бренд: SAI HVAC Страницы: 16

Бренд: Saitek Страницы: 15

Бренд: saia-burgess Страницы: 203

Бренд: Sailor Страницы: 1

Бренд: vacuubrand Страницы: 12

Бренд: Vacon Страницы: 47

Бренд: Vacon Страницы: 40

Бренд: Valco baby Страницы: 24

Бренд: Zennio Страницы: 30

Бренд: Zeta Страницы: 13

Бренд: brel-motors Страницы: 2

Бренд: National Instruments Страницы: 4

Бренд: Z-Wave Страницы: 9

Бренд: Hard Head Страницы: 10

Бренд: Barco Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды