Harsen GU641B Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 60

background image

Manual

HM1016ER1

Panel Operation

Harsen

®

Page 6/54

START Button / LED / Return

The push button is used for manually start the Genset. When controller
is running in MANUAL mode, press this button to start the generator.

When in parameters setting mode, this button is used to return.

STOP / RESET Button / “

→

→

→

→

” Move Setting

The  Push  button  is  used  for  manually  stops  the  Genset.  No  matter
what  mode  the  controller  is  running,  press  and  hold  this  button  for
2sec to stop the generator, the mode of the controller will be default to
“MAN”  mode  automatically  from  “AUTO”  or  “TEST”  mode  and  the
generator  will  be  shut  down  after  cool  down  period,  during  the  cool
down  period  if  you  press  and  hold  this  button  for  2sec  again,  the
generator will be shut down immediately.

If failure occurs, press this button, the shutdown alarm lockout can be
cleared.

When in parameters setting mode, this button is used to move to next
parameters setting position.

C/O Button

There are 2 C/O buttons respectively beside the Mains and Gen icons.
They are used to close/open the switches of Mains and Gen when
controller is running in MANUAL mode.

Shutdown Alarm (FAILURE) LED

The LED will illuminate permanently when shutdown alarm occurs.

Pre-alarm (WARNING) LED

The LED will illuminate permanently when pre-alarm occurs.

GEN. Normal LED

Gen. normal LED will illuminate after both voltage and frequency of the
Gen. reach loading voltage and frequency.

GCB/MCB Closed LED

LED will illuminate when GCB/MCB is closed and power supplied by
Gen / Mains, LED will flash when GCB / MCB failure occurs.

MAINS Normal LED

Mains normal LED will illuminate after both voltage and frequency of
the Mains reach the preset value range.

«
...
9
10
11
12
13
...
»

Содержание GU641B





























































Отзывы:

Нет отзывов

Похожие инструкции для GU641B

Бренд: D-Link Страницы: 40

Бренд: Garmin Страницы: 12

Бренд: Ebyte Страницы: 34

Бренд: XVision Страницы: 28

Бренд: YASKAWA Страницы: 61

Бренд: DayTronic Страницы: 22

Бренд: DayTronic Страницы: 414

Бренд: Paradox Страницы: 32

Бренд: WAREMA Страницы: 112

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

Бренд: oventrop Страницы: 64

LDSBus LC020101A-F

Бренд: BRT Systems Страницы: 15

Бренд: GeoVision Страницы: 21

Бренд: Mitsubishi Страницы: 30

Бренд: Hahnel Страницы: 36

Бренд: maxon motor Страницы: 44

Бренд: Resol Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды