Harsen GU641B Скачать руководство пользователя страница 26

Страница: 26 / 60

Manual

HM1016ER1

Parameters Setting

Harsen

Page 21/54

7. Parameters Setting

7.1 SYSTEM:

NO.

Items

Preset

Value Range

1.1

CT Ratio

200

1 to 1200

1.2

VT Ratio

1.0

1.0 to 25.0

1.3

Rated ph-voltage

220

45 to 9999VAC

1.4

Rated current

1000

0 to 6000A

1.5

Rated active power

500

0 to 3000KW

1.6

Voltage Type

1 to 5

1.7

Comm. Address

1 to 247

1.8

Startup mode

0 MAN /1 AUTO /2 the same as last time

1.9

Auto scroll time

1 to 60s / 0 Not used

1.10

Default settings

1.11

Password

0000 to 9999

1.12

Firmware update

Menu descriptions:

CT Ratio:

The current is derived from CT on generator.

Secondary current on CT is fixed at 5A.

Used to calculate for GEN: KVA, KW and PF.

Used for shutdown alarm: over current, overload, etc.

VT Ratio:

The voltage is derived from VT on Gen and Mains.

Used to detect frequency of Gen and Mains.

Used to calculate for GEN: KVA, KW and PF.

Used for shutdown alarm: over/under voltage, overload, etc.

Rated ph-voltage:

Used to define the rated voltage (phase to neutral) of Gen and Mains, rated VPh-Ph = “Rated ph-

voltage” * 1.732.

Reference value for judging over/under voltage.

Rated current:

Used to define the rated current of generator.

Reference value for judging current.

Содержание GU641B





























































Результаты поиска

Содержание GU641B

Отзывы:

Похожие инструкции для GU641B

Бренды по названию

Популярные бренды

Harsen GU641B, Руководство пользователя

Результаты поиска

Содержание GU641B

Отзывы:

Похожие инструкции для GU641B

Бренды по названию

Популярные бренды