Harsen GU641B Скачать руководство пользователя страница 33

Страница: 33 / 60

Manual

HM1016ER1

Parameters Setting

Harsen

Page 28/54

MPU input:

Used to configure whether magnetic pick-up is used or not.

When parameter is configured as “1”, magnetic pick-up is used for the signal source of the engine

speed. When parameter configured as “0”, the magnetic pick-up is not used, the engine speed is

calculated from the frequency of the generator.

RPM = (Hz * 60) / Pair of Poles. For example: the frequency of generator is 50Hz, when Pair of

Poles configured as 2, RPM = (50*60)/2 = 1500 (RPM).

Fly wheel teeth:

Used to configure there are how many teeth on the fly wheel.

Set pickup now:

If user does not know the fly wheel teeth, to calculate the fly wheel teeth automatically via the

measuring Gen frequency and MPU frequency.

Fly wheel teeth = (f1 * Pair of Poles) / f2, {f1 is MPU frequency, f2 is Gen frequency}.

Operating procedure:

Configure the parameter of “MPU input” as “0”.

Start the Genset, choose “Set pickup now” from the menu after the Genset running normally,

the parameter of “fly wheel teeth” will be automatically calculated at that time.

Configure the parameter of “MPU input” as “1” to finish the setting.

NOTE:

This function is only used for the debug of the controller and Genset.

Please do not implement this function when no RPM signal input.

Pair of Poles:

Used to configure the poles of excitation winding of the alternator.

Use to calculate PRM when the measured speed of controller is from the frequency signal of

generator.

Fuel mode:

Used to configure the type of engine fuel valve (details refer to 4.5).

N.C. type means the fuel channel is closed when fuel can not be used; N.O. type means the fuel

channel is opened when fuel can not be used.

T-sensor type:

Used to configure the type of HET sensor.

Optional kinds of built-in HET sensors in the controller.

Code

Mode

Note

close for high temperature

open for high temperature

VDO 120

℃

VDO 150

℃

Datcon

Murphy

Pt100

Pre-set 1

Содержание GU641B





























































Результаты поиска

Содержание GU641B

Отзывы:

Похожие инструкции для GU641B

Бренды по названию

Популярные бренды

Harsen GU641B, Руководство пользователя

Результаты поиска

Содержание GU641B

Отзывы:

Похожие инструкции для GU641B

Бренды по названию

Популярные бренды