Harsen GU641B Скачать руководство пользователя страница 6

Страница: 6 / 60

Manual

HM1016ER1

Description

Harsen

Page 1/54

1. Description

GU641B is a new generation Automatic Mains (Utility) Failure module for single Genset, which adopts

bran-new outline configuration, focus on the requirements of customers, and perfectly improves the

performance of controller. It fully meets the auto control requirements of different kinds of Genset for

user or special assembly factory.

The module also monitors and protects the engine, indicating operational status, fault conditions and

metering on the front panel LCD and LED.

True RMS measure of voltage and current.

2 analog inputs for kinds of optional built-in sensors, parameters also can be configured by user.

More outputs of configurable auxiliary control relays.

More configurable isolated digital inputs.

Buttons on control panel are used for selecting control modes, starting and stopping the operating

procedure, displaying data and modifying the parameters. LED indicators are used for indicating

the operation mode of controller and the running status of Genset, and LCD displays each

measuring parameter and status.

Flexible equipped with RS485, RS232 and USB, realizing remote monitor; or communicated with

PC, fully realizing functions of remote signaling, telemetering and remote control, can read and set

the running parameters of controller.

All connections of the controller are by secure plug and socket, for ease and convenience to connect,

move, maintain and replace the device.

This manual is only suitable for GU641B Automatic control module, user must carefully read

this manual first.

Содержание GU641B





























































Результаты поиска

Содержание GU641B

Отзывы:

Похожие инструкции для GU641B

Бренды по названию

Популярные бренды

Harsen GU641B, Руководство пользователя

Результаты поиска

Содержание GU641B

Отзывы:

Похожие инструкции для GU641B

Бренды по названию

Популярные бренды