manualshive.com logo in svg

Harris Intelligent Transmitter Platinum-i Series, Техническое руководство

Интеллектуальный передатчик серии Platinum-i от Harris - это инновационное устройство для передачи данных. Техническое руководство можно скачать бесплатно на сайте manualshive.com для ознакомления с функционалом и настройками устройства. Обеспечьте надежную работу вашей системы с помощью этого передатчика высокого качества.

Поделиться
Скачать
background image

 

______________________________________________

HARRIS

 

 

888-9058-001 

WARNING: Disconnect and lockout AC primary power prior to servicing

 

132

 
 

5.2.1.1 Features of the 376 module include: 

a.

 

Built-in CAN (Controller Area Network) bus controller 

 

b.

 

16 A/D inputs for analog metering 

 

c.

 

A serial EEPROM for non-volatile memory storage 

 

d.

 

A built in clock running at 4.194MHz which will let the micro run at 16- 

25MHz 

 

e.

 

Power failure detection 

 

f.

 

A watchdog which will reset the micro if it is not triggered at least every 1.6 

seconds (this time interval will change depending on the application). A discrete 
logic device or CPLD is provided on the motherboard to act as an I/O expansion 
device and as life support if the micro module fails. 
 

g.

 

Multiple I/O lines whose direction of signal flow is based on the flash memory 

programming. These could be control or status, inputs or outputs, depending on 
the particular use. 

 

The main responsibility of the micro module is control of the CPLD and the reporting 
and receiving of information over the CAN bus. This means that the CPLD will 
continue to monitor and protect the systems to which it is connected even if the micro 
module fails. However, there will be no reporting of information to the rest of the 
transmitter system since access to the CAN bus is gone without the micro module. 
 

5.2.2 CPLD, Complex Programmable Logic Device 

The transmitter control board with the micro module also incorporate a CPLD 
(Complex Programmable Logic Device) with the exception of the module controllers. 
The CPLD is not a microprocessor but is actually just programmed discrete logic and is 
therefore very stable and reliable. The CPLDs in the transmitter perform two vital 
functions in terms of control and transmitter monitoring: 

• 

I/O Expansion 

• 

Life Support Backup 

 

5.2.2.1 I/O Expansion 

Each Micro Module only has a limited number of Input/Output or I/O lines available. 
The CPLDs provide a way to easily expand the available I/O ports on each control 
board. Basically, the CPLDs are actually controlling and monitoring the I/O for each 
control board. The micro module is taking that information and relaying it, via the CAN 
bus, to the Main Controller for display on the front panel control screen or a remote 
control system. If the micro module wants to send a control command, it simply 

Содержание Intelligent Transmitter Platinum-i Series





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Intelligent Transmitter Platinum-i Series

YOKOGAWA Dpharp vigilantplant EJA Series User Manual preview
Dpharp vigilantplant EJA Series
Бренд: YOKOGAWA Страницы: 31
teko Astra-TRC Operation Manual preview
Astra-TRC
Бренд: teko Страницы: 2
E+H Cerabar T PMP 135 Technical Information preview
Cerabar T PMP 135
Бренд: E+H Страницы: 12
YOKOGAWA vigilantplant YTA70 User Manual preview
vigilantplant YTA70
Бренд: YOKOGAWA Страницы: 5
CAMDEN Lazerpoint CM-TX-9 Installation Instructions preview
Lazerpoint CM-TX-9
Бренд: CAMDEN Страницы: 3
M-system CTS2 Instruction Manual preview
CTS2
Бренд: M-system Страницы: 3
Dittel FSG 40S Manual preview
FSG 40S
Бренд: Dittel Страницы: 38
NAPCO GEMC-WL-WD2 Installation Instructions preview
GEMC-WL-WD2
Бренд: NAPCO Страницы: 4
TRUEYES Air-T CO2 User Manual preview
Air-T CO2
Бренд: TRUEYES Страницы: 11
Icom UT-112 Installation And Programming preview
UT-112
Бренд: Icom Страницы: 2
Avantree BTTC-318 User Manual preview
BTTC-318
Бренд: Avantree Страницы: 8
J&E Hall Danfoss AKS 41 Manual preview
Danfoss AKS 41
Бренд: J&E Hall Страницы: 18
Epson WirelessHD transmitter User Manual preview
WirelessHD transmitter
Бренд: Epson Страницы: 64
Epson WirelessHD User Manual preview
WirelessHD
Бренд: Epson Страницы: 64
GEV 003170A Assembly preview
003170A
Бренд: GEV Страницы: 30
Icom IC-F51V Instruction Manual preview
IC-F51V
Бренд: Icom Страницы: 50
Teradek Clip Getting Started preview
Clip
Бренд: Teradek Страницы: 2
Ritron SPX-200 Maintenance/Repair/Operating Manual preview
SPX-200
Бренд: Ritron Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды