Harris CZ1000F Скачать руководство пользователя страница 14

Страница: 14 / 162

Table of Contents

(continued)

888-2685-001

12/24/07

WARNING: Disconnect primary power prior to servicing.

Objective. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Requirement(s) . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Setup and Test Equipment . . . . . . . . . . . . . . . . 4-7
Power Measurement Procedure . . . . . . . . . . . . 4-8
Power Measurement Test Results. . . . . . . . . . . 4-8

Frequency Tolerance . . . . . . . . . . . . . . . . . . . . . . 4-9

Objective. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Requirement(s) . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Setup and Test Equipment . . . . . . . . . . . . . . . . 4-9
Frequency Tolerance Procedure . . . . . . . . . . . 4-10
Frequency Tolerance Test Results . . . . . . . . . 4-10

Non-Linear Precorrection (Shoulders & Amplitude

Response). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Objective. . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-11
Requirement(s) . . . . . . . . . . . . . . . . . . . . . . . .  4-11
Setup and Test Equipment  . . . . . . . . . . . . . . .  4-11
Non-Linear Precorrection Procedure . . . . . . . 4-12
Non-Linear Precorrection Test Results. . . . . . 4-13

Out of Band Emissions . . . . . . . . . . . . . . . . . . . 4-13

Objective. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Requirement(s) . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Setup and Test Equipment . . . . . . . . . . . . . . . 4-14
Out of Band Emissions Procedure . . . . . . . . . 4-15
Out of Band Emissions Test Results. . . . . . . . 4-16

Spurious Emissions (including 2nd & 3rd harmonics)

4-19

Objective. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Setup & Test Equipment. . . . . . . . . . . . . . . . . 4-20
Spurious Emissions Procedure . . . . . . . . . . . . 4-20
Spurious Emissions Test Results . . . . . . . . . . 4-22

Linear Precorrection (Group Delay & Amplitude

Response). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

Objective. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
Setup & Test Equipment. . . . . . . . . . . . . . . . . 4-26
Spurious Emissions Procedure . . . . . . . . . . . . 4-26

Spurious Emissions Test Results . . . . . . . . . .  4-27
Linear Precorrection Procedure . . . . . . . . . . .  4-30
Linear Precorrection Test Results  . . . . . . . . .  4-31

Modulation Error Ratio (MER) . . . . . . . . . . . . 4-32

Objective  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-32
Requirement(s) . . . . . . . . . . . . . . . . . . . . . . . .  4-32
Setup and Test Equipment . . . . . . . . . . . . . . .  4-32
Modulation Error Measurement Procedure . .  4-34
Modulation Error Results . . . . . . . . . . . . . . . .  4-35

Meter Readings . . . . . . . . . . . . . . . . . . . . . . . . .  4-36
System VSWR Plots . . . . . . . . . . . . . . . . . . . . .  4-37
Software Versions . . . . . . . . . . . . . . . . . . . . . . .  4-39

Appendix A - Linux Data Capture & Processing 4-40

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-40
Required Equipment . . . . . . . . . . . . . . . . . . . . .  4-40
Block Diagram  . . . . . . . . . . . . . . . . . . . . . . . . .  4-40
1PPS Source Setup . . . . . . . . . . . . . . . . . . . . . .  4-41

FSQ Connections . . . . . . . . . . . . . . . . . . . . . . 4-41
FSQ Settings. . . . . . . . . . . . . . . . . . . . . . . . . . 4-43

Setting Static IP Address for FSQ & Linux Machine

4-43

For the FSQ . . . . . . . . . . . . . . . . . . . . . . . . . . 4-44
For Linux Laptop . . . . . . . . . . . . . . . . . . . . . . 4-44

Capturing and Processing Data. . . . . . . . . . . . . 4-45

Setting Flo Signal Parameters  . . . . . . . . . . . .  4-45
Performing the Measurement . . . . . . . . . . . . .  4-46
Looking at the Results . . . . . . . . . . . . . . . . . .  4-46
Moving Results to Flash Drive. . . . . . . . . . . .  4-46

Appendix B - Generating a CW Tone . . . . . . . . . 4-48

Section 5

Replacement Procedures

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
PA Module Removal . . . . . . . . . . . . . . . . . . . . . . . 5-1

CZ1000F PA Module Air Block . . . . . . . . . . . . . 5-1
PA Module Pallet Replacement . . . . . . . . . . . . . 5-3

Power Supply Module Replacement . . . . . . . . . . .  5-6
Circulator Removal/Replacement . . . . . . . . . . . . .  5-7
Blower Assembly Removal . . . . . . . . . . . . . . . . . .  5-9

Section 6

ISP (In-System Programming)

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-1
Installing the ISP Program. . . . . . . . . . . . . . . . . . .  6-2
ISP Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-2

Содержание CZ1000F



































































































































































Результаты поиска

Содержание CZ1000F

Отзывы:

Похожие инструкции для CZ1000F

Бренды по названию

Популярные бренды

Harris CZ1000F, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание CZ1000F

Отзывы:

Похожие инструкции для CZ1000F

Бренды по названию

Популярные бренды