Operation
131
•
•
•
•
•
•
Auto Mode Tracking – Disabled (Default)
1. The displayed weight mode will remain unchanged when TARE or
ZERO is pressed.
2. To change the displayed weight mode, press the MODE button from
the front panel display
3. or send the DISPLAY MODE command over communications.
4. The ZERO command functions in both NET or GROSS mode at any
time.
Auto Mode Tracking – Enabled
Step 1. The displayed weight mode will automatically change to NET when TARE is
pressed on the front panel display or when a TARE command is sent over
communications.
5. The displayed weight mode may also be changed at any time by pressing the
MODE button on the front panel display or by sending the DISPLAY
MODE command over communications.
6. Sending the
TARE AMOUNT=0.0000
command will remove the TARE
weight from memory and cause the displayed weight mode to automatically
switch to display the GROSS weight. (AUTO MODE TRACKING DOES
NOT FUNCTION WHILE IN COUNT MODE)
7. The ZERO button only functions on the front panel display when the
instrument is in GROSS mode.
a.
If an operator presses ZERO button while in NET mode, the display
will message the user “ZERO FAIL - CHANGE TO GROSS
MODE TO USE ZERO SCALE”
6. The ZERO command functions in both NET and GROSS modes when sent
over communications.
If the instrument is in NET mode when the ZERO command is sent over communications,
the display will automatically switch to showing GROSS mode after the ZERO command
is sent.
Count Operations
On the HI6500 series instrument display
, select the Operations menu and use the UP or
DOWN button to select the Piece Count submenu. Select Count Enable to allow the option
of running the instrument in count mode. Piece Count can be displayed on the main screen
by pressing the MODE button and cycling through to the count mode: GROSS > NET >
COUNT >
Содержание HI 6500 Series
