136
Chapter
7
•
•
•
•
•
•
Once Instruments are Wired and In Place
Connect the display to the port on the instrument. If the Split Screen Display Mode is not
enabled, the user will be connected to a single unit.
Enter the Display->Split Screen menu to enable the Split Screen Display Mode. Here you
can send a Discover command and the display will find all compatible instruments on the
RS-485 Display Network. The product serial codes for each instrument will be listed as
they are found. Once the discovery process has completed the menu will switch to the
Display Order interface and attempt to connect to each discovered instrument. As
instruments connect their Instrument IDs will be displayed next to their product serial
codes.
Reordering Units
When a Discovery completes or when Display Order is selected in the Display->Split
Screen menu, the Display Order interface will open. The order which instruments are listed
determines their locations on the Split Screen Summary Page. Instruments are displayed
left to right, top to bottom.
From the front panel display, use the UP and DOWN buttons to select unit to move to
another location. Press enter to select the unit. Use UP and DOWN button to move it
to the desired location. Once in the desired position, press Enter do complete the move.
Repeat with any other unit you wish to move in the display.
Hiding Units by Changing the Number of Units to Display
The Num Display parameter sets the number of instruments to display on the Split Screen
Summary Page. Sections higher than the number of instruments to display are left blank
and cannot be selected from the Split Screen Summary Page.
1
2
3
4
Содержание HI 6500 Series
