manualshive.com logo in svg

GSE Agrifeed 5500, Справочное руководство

Поделиться
Скачать
GSE Agrifeed 5500 Скачать руководство пользователя страница 68

64 

 
 

 

 

 

Figure 35:  Remote Display Connector 

 

Table 10:  Connector Pin Out 

 

7.1.2.1 

Remote Display Connection (Part Number 201500-09021) 

The interface cable is already installed so there is no need to open the 
unit unless another remote display is going to be added. Refer to the 
previous instructions (Install Part Number 2001500-09020) to add 
another remote display.   
 
The Agrifeed 5500 Remote Display connector, an 8 pin receptacle, uses a 
socket mating plug (GSE part number 26-20-1160).  When matching the 
sockets of the plug to the pins of the receptacle, be sure to reference the 
pin-out labeled on the bottom of the Agrifeed 5500 enclosure. This pin-
out label should also be referenced to match the wires of the cable to the 
Agrifeed 1500 remote display connector. 
 
The Model 1500 has annunciators for the Gross and Net modes.  The 
Quantity mode is designated by all annunciators turned off.  
 

Pin Name Description 

1 DAT  Positive 

data 

line 

2 

DAT - 

Negative data line 

3 CLK  Positive 

clock 

line 

4 

CLK - 

Negative clock line 

5 

DCS 

Positive data clear send line 

6 

DCS -  

Negative data clear send line 

7 

+ 5V 

Positive 5 volts 

8 GROUND 

Common 

ground 

Pin 8

Pin 1 

Содержание Agrifeed 5500









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды