manualshive.com logo in svg

GSE Agrifeed 5500, Справочное руководство

Поделиться
Скачать
GSE Agrifeed 5500 Скачать руководство пользователя страница 61

57 

6.2.1  Reload Agrifeed 5500 Custom Program 

If you experience a Code 26 error or Code 60 (New Eprom) on the 
Agrifeed 5500 unit, the following steps will reload the program back into 
the indicator. Please be advised that reloading this program may take 
several minutes to complete.  All recipe, ingredient and pen information 
will be deleted.  

1.

 

First press 

[CLR] [CLR]

, then key in 

100 [NET\GROSS]

. 

2.

 

The display will prompt 

“

Keyin Code”

.

  

3.

 

Key in the access code 

23640 [ADD RECIPE] [ENTER]

. 

4.

 

Next, key in 

65001 [NET\GROSS]

 to access the 

“Deflt All”

 

prompt.

 

 

5.

 

Press 

[TARE]

 to display 

“Agri-feed”

.

  

6.

 

Press 

[ENTER]

 to display  

“Sure?”

.

  

7.

 

After a moment the display will prompt 

“Enter=Dflt”

.

 

8.

 

Press 

[ENTER] [ENTER]

 to begin loading the Agrifeed 

program.  

 
If the display went right to the Agrifeed start up screen, the following 
steps will load the program from the eprom into the indicator. Please be 
advised that reloading this program may take several minutes to 
complete.  All recipe, ingredient and pen information will be deleted.  
 

1.

 

Turn the unit off, hold down the 

[CLR]

 key and turn the unit 

back on. Hold down the 

[CLR]

 key until the display reads 

“macro disbl”.

 

2.

 

Key in 

100 [NET\GROSS]

. 

3.

 

The display will prompt 

“

Keyin Code”

.

  

4.

 

Key in the access code 

23640 [ADD RECIPE] [ENTER]

. 

5.

 

Next, key in 

65001 [NET\GROSS]

 to access the 

“Deflt All”

 

prompt.

 

 

6.

 

Press 

[TARE]

 to display 

“Agri-feed”

.

  

7.

 

Press 

[ENTER]

 to display 

“Sure?”

.

  

8.

 

After a moment the display will prompt 

“Enter=Dflt”

.

 

9.

 

Press 

[ENTER] [ENTER]

 to begin loading the Agrifeed 

program. 

 

Содержание Agrifeed 5500









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды