GSE Agrifeed 5500 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 72

background image

56

6.2 Hardware

Problem Error Messages

Message Description

17 A/D BAD!

The processor has detected a problem with the A/D chip.

18 BufSzMax!

The accumulative total buffer size for both the TX and
RX buffers of all 4 COMM ports on the 650 is 4096
bytes.

19
x06\x44\x61ta&Stop

Certain combinations of protocol are not available. The
protocol combination selections are in P201, P202 and
P203. This error occurs if an illegal protocol
combination is selected.

20 Deflt A/D

This message is displayed for 1 second. It will be
displayed if the A/D calibration data gets corrupted by
whatever means. This message will also be displayed on
power-up if the check-sum for the A/D data is corrupted.

21 WriteNVErr

Error reading data from the EEPROM. Call GSE
Distributor.

22 ReadNVErr

Error writing data to the EEPROM. Call GSE
Distributor.

23 CheckNVPar

Supplementary error message for above errors.

24 NVParFull!

The setup being attempted requires more EEPROM than
is currently installed.

25 DefltSetup

Upon power-up the indicator has not found the proper
codes. Therefore, all parameters have been reset to
factory default values.

26 Bad Setup

The stored data has a checksum error. Check all
parameters or re-load setup. Refer to section 6.2.1 for
instructions on reloading Agrifeed 5500 program.

27 RE-BOOT!

The indicator cannot use the EEPROM for data storage,
so it is attempting to power-up again to cure the problem.

28 NoRAMAVAIL

The current setup requires more RAM than is currently
installed. Either contact your dealer or the manufacturer.

29 PIN error

This message will appear on power-up or setup if the
ram is corrupted in the PIN section. Call GSE
Distributor. The access code is then defaulted to the
manufacturer (GSE) access code. Also refer to Error 11.

«
...
58
59
60
61
62
...
»

Содержание Agrifeed 5500









































































Отзывы:

Нет отзывов

Похожие инструкции для Agrifeed 5500

Бренд: Eaton Страницы: 21

Бренд: AC Schnitzer Страницы: 16

Бренд: Obelink Страницы: 2

Бренд: LAZER Страницы: 6

Бренд: Talkswitch Страницы: 334

Бренд: Tait Страницы: 41

Бренд: Tait Страницы: 149

Бренд: Tait Страницы: 132

Бренд: Vaisala Страницы: 24

Бренд: JANE Страницы: 21

Бренд: aquatherm Страницы: 32

Бренд: Metz Страницы: 112

Бренд: AIA Страницы: 8

Бренд: Eco Страницы: 34

Бренд: Tripp Lite Страницы: 2

Бренд: Victory 4x4 Страницы: 13

Бренд: Masterack Страницы: 4

Бренд: Over Armour Offroad Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды