GreenMachine ZR10945, Руководство оператора

Страница: 47 / 60

47
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
1. Check Spark. Remove air filter cover. Remove spark plug
from cylinder. Reattach the spark plug wire and lay spark
plug on top of cylinder with the metal part of plug touching the
cylinder. Pull the starter rope and watch for spark at spark
plug tip. If there is no spark, repeat test with a new spark plug.
2. With the ignition switch off, remove spark plug. Move choke
lever to run position (pushed in completely) and pull starter
cord 15 to 20 times. This will clear excess fuel from engine.
Clean and reinstall spark plug. Pull starter three times with
choke lever at run. If engine does not start, move choke lever
to choke and repeat normal starting procedure. If engine still
fails to start, repeat procedure with a new spark plug.
* Contact a Green Machine Servicing Dealer for carburetor
adjustment.
* Contact a Green Machine Servicing Dealer for carburetor
adjustment.
1. Use fresh fuel and the correct 2-cycle oil mix ratio.
2. Clean per instruction in Maintenance-Air Filter Section.
3. Clean per instructions in Maintenance-Spark Arresting
Muffler Section.
4. * Contact a Green Machine Servicing Dealer for carburetor
adjustment.
Turn idle speed screw “T” [see illustration (A)] clockwise to
increase idle speed. (If chain turns at idle, turn idle speed screw
“T” counterclockwise to decrease speed). Wear protective
equipment and observe all safety instructions.
1. Oil tank should be filled every time that fuel tank is filled.
2. Tension chain per instructions in Operation-Chain Tension
section.
3. Run at half throttle 30 to 45 seconds. Stop saw and check
for oil dripping from Safe-T-Tip and guide bar. If oil is present
the chain may be dull or bar may be damaged. If no oil on Safe-
T-Tip, contact a Green Machine Servicing Dealer.
1. Release chain brake, see Operation-Chain Brake Section.
2. Retension chain, refer to Assembly-Chain Tension Section.
3. Refer to Assembly-Assembling the Bar and Chain Section.
4. Inspect guide bar and chain for damage.
Engine will not start:
(Make sure Ignition switch
is in start position “I”.)
Engine starts but will not ac-
celerate properly:
Engine starts but will not run
properly at high speed .
Engine does not reach full
speed and / or emits exces-
sive smoke:
Engine starts, runs, and ac-
celerates but will not idle.
Bar and Chain Running Hot
and Smoking:
Engine starts and runs, but
chain is not rotating:
Using Troubleshooting Chart
If you are experiencing a problem that is not listed in this chart, see your Green Machine Servicing Dealer for service.
When you have checked all the possible causes listed and you are still experiencing the problem, see your Green Machine Servicing
Dealer.
1. No spark
2. Flooded engine.
Carburetor requires “L” (Low jet) adjustment.
Carburetor requires “H” (High jet) adjustment.
1. Check oil fuel mixture.
2. Air filter dirty.
3. Spark arrester screen dirty.
4. Carburetor requires “H” (High jet) adjustment.
Carburetor requires adjustment.
1. Chain oil tank empty.
2. Check chain tension for overtight condition.
3. Check for oiler function.
1. Chain brake engaged.
2. Chain tension too tight.
3. Check guide bar and chain assembly.
4. Check guide bar and chain for damage.
*
Note: This engine complies with EPA (Environmental Protection Agency) and CARB (California Air Resource Board) regulations which require
exhaust emission control. As a result, the carburetor adjustment needles are equipped with plastic caps that limit the rotation from the original
factory adjustment. If your unit exhibits specific performance problems that can not be corrected by the Trouble Shooting Section, the unit should
be taken to a Green Machine Servicing Dealer for repair.
T
H
L
A