GE Digital Energy LP 33 Series Скачать руководство пользователя страница 6

Страница: 6 / 103

Modifications reserved

Page 6/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

1 SAFETY RULES

With this document,

gives to the user all the necessary information about the correct use of the UPS.

Please read carefully this

Operating Manual

before installing or operating the UPS.

We recommend that this manual be kept next to the UPS for future references.

If any problems are encountered with the procedures contained in this manual, please contact the

nearest

Service Centre

before you proceed.

All UPS installation, maintenance and service work should be performed by qualified service personnel
only.

The KNOWLEDGE and the FULLY compliance of the safety instructions and
the warning contained in this manual are

THE ONLY CONDITION

to avoid any dangerous situations during installation, operation,

maintenance work, and to preserve the maximum reliability of the UPS
system.

NOTE !

LP 33 Series 60 - 80 - 100 - 120 kVA

is a Category C2 UPS Product

(Class A), according to IEC 62040).
Installation restrictions or additional measures may be needed
to prevent disturbances

ATTENTION !

While every care has been taken to ensure the completeness
and accuracy of this manual,

assumes no responsibility or

liability for any losses or damages resulting from the use of the
information contained in this document.

, refuses any responsibility in case of non-observance,

unauthorised alterations or improper use of the

delivered UPS.

Содержание Digital Energy LP 33 Series








































































































Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды

GE Digital Energy LP 33 Series, Руководство по эксплуатации

Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды