GE Digital Energy LP 33 Series Скачать руководство пользователя страница 25

Страница: 25 / 103

Modifications reserved

Page 25/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

5.3.2 Storage of the battery

In case of extended storage, when the delivery includes maintenance free batteries, keep in mind that

they are subject to auto-discharging process

To avoid permanent damages to the battery, you must observe the following instructions:

•

The storage time without charging the battery depends on the temperature of the storage ambient.

•

The optimal ambient temperature for the batteries is

20°C

(68°F).

For storage temperature higher than

20°C

(68°F), the storage time will decrease.

•

Each additional

10°C

(18°F) over the nominal temperature of

20°C

(68°F) will decrease the storage

time, without freshening charge, by half.

In case of a

maintenance free battery

, the storage time without charging the

battery

approximately:

6 months with storage temperature 20°C (68°F)

3 months with storage temperature 30°C (86°F)

2 months with storage temperature 35°C (95°F)

NOTE !

In case of

battery

storage pay

attention to:

FRAGILE

SENSITIVE

TO DAMPNESS

TO HEAT

SENSITIVE

TO FROST

SENSITIVE

Содержание Digital Energy LP 33 Series








































































































Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

GE Digital Energy LP 33 Series, Руководство по эксплуатации, Страница: 25 / 103

Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы: