GE Digital Energy LP 33 Series Скачать руководство пользователя страница 88

Страница: 88 / 103

Modifications reserved

Page 88/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

8.2.5 Reconnect a UPS unit to a Parallel System

WARNING !

Before connecting hazardous voltages, make sure that:

•

The connection to the electrical system has been performed by qualified personnel;

•

The

equipment frame

has been correctly grounded to the

main earth

;

•

Make sure that

mains input

protection is removed;

•

All the

panels

removed to allow the UPS connection have been correctly reinstalled;

•

The UPS switches

and

are open (Pos. 0);

•

The external

battery

fuses are removed.

This procedure must be performed when the

load

is supplied by the other units of the

UPS Parallel

System

and an additional unit must be switched ON and connected to the parallel bus in order to share

the load with each other.

This unit must be completely switched OFF and not powered.

1. Switch-ON the mains voltage from the input distribution (both rectifier and bypass if separated)

on this UPS unit.

Overall test results

Test1 OK

Test7 OK

Test2 OK

Test8 OK

Test3 OK

Test9 OK

Test4 OK

Test10 OK

Test5 OK

Test11 OK

Test6 OK

The UPS performs a

SELFTEST

A successful termination of the tests will be indicated with Overall
test results

“OK”

Commissioning cannot be continued should one or more tests result
to be negative.
Please contact in this case your

Service Centre

2. Insert the external battery fuses on this unit

In case of GE battery cabinet: insert the fuses in their place and close fully the cover of fuse-holder by

using correctly the handle.

3. Close output switch Q1 (Pos. I) on this UPS unit.

Home\Meter

BOOSTER

f :

50.0

L1 :

397

L2 :

395

L3 :

393

Vp :

400

Vn :

400

Verify on this UPS unit, selecting the screen

METERING/BOOSTER/

and

, that the booster voltage has reached about

400 Vdc

4. Insert the inverter by pressing

“

Inverter ON

”

( I ) key on this UPS unit.

When the

inverter

will be synchronised, the unit will be

automatically connected with the

parallel bus-bar

and the

load

will

be shared with the other units.

LED Alarm

turn Off and the

LED Operation

must be lit.

The

synoptic diagram

, on all UPS units, must display the status

“

LOAD SUPPLIED BY INVERTER

”

END OF PROCEDURE

Содержание Digital Energy LP 33 Series








































































































Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды

GE Digital Energy LP 33 Series, Руководство по эксплуатации

Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды