GE Digital Energy LP 33 Series Скачать руководство пользователя страница 48

Страница: 48 / 103

Modifications reserved

Page 48/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

5.9 UPS FUNCTIONING AS FREQUENCY CONVERTER

When the UPS

LP 33 Series

is delivered as frequency converter (different output frequency with respect

to the input frequency),

the automatic bypass and manual bypass functions are disabled

Therefore the

load

cannot be transferred to mains in case of overload, short circuit, or inverter failure.

In cases where the UPS needs to be powered down for maintenance purposes, the critical load must
also be powered down during this time.

When the set-up parameters of the UPS are set for

frequency converter

, the

ECO Mode

operation is

automatically disabled.

The UPS delivered as

frequency converter

has the following differences:

•

Automatic

bypass disabled

by setting of dedicated parameter (access protected by password

reserved to service engineer).

•

The handle of the switch

Q2 - manual bypass

is removed to avoid accidental wrong manipulations.

•

Mains bypass

disabled by removing the fuse

fitted on the board

P2 – Power Supply

WARNING !

In case a UPS delivered as frequency converter should be set on site for UPS
standard version, the operation must be performed by a qualified service engineer.

Notices for installation:

•

For UPS with

common AC input

follows the standard procedure described in

Section 5.8.1

Notices for start up procedures:

•

Follow the standard procedure indicated in

Section 8.1

Notices for shutdown procedures:

•

Follow the standard procedure indicated in

Section 8.1

NOTE !

The inverter can be turned off only by pressing the push-button

Total Off

Содержание Digital Energy LP 33 Series








































































































Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды

GE Digital Energy LP 33 Series, Руководство по эксплуатации

Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды