GE Digital Energy LP 33 Series Скачать руководство пользователя страница 71

Страница: 71 / 103

Modifications reserved

Page 71/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

During the first commissioning

LP 33 Series

requests a set up of the UPS configuration parameters

presented in the following screens.

Without such configuration it is not possible to continue with the commissioning procedure.

WARNING !

The setup of the UPS configuration parameters must be done only by QUALIFIED
AND TRAINED PERSONNEL.
The setup of mistaken values could compromise the integrity and reliability of the
UPS.

In this mode the keys perform the following functions:

Confirm the selection made and select the next parameter.

ESC

Re-establish default value.

Modify or insert the selected value.

Save the configuration of set parameters.

Configuration

DISPLAY CONFIGURATION

Select language

ENGLISH

ESC

DISPLAY CONFIGURATION screen

Select language

This parameter allows the choice of language used to display

the information.

Configuration

UPS CONFIGURATION

Input frequency

Output frequency

50 Hz

Inverter voltage

230

ESC

UPS CONFIGURATION screen

Input frequency

Input frequency value (*50Hz).

Output frequency

Inverter output frequency value (*50Hz).

Inverter voltage

Output voltage PHASE/NEUTRAL of the inverter (220V/230V/240V).

)

Configuration of the frequency to 60Hz requires the
intervention of a

Service Centre

Continue

►

Содержание Digital Energy LP 33 Series








































































































Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды

GE Digital Energy LP 33 Series, Руководство по эксплуатации

Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды