GE Digital Energy LP 33 Series Скачать руководство пользователя страница 84

Страница: 84 / 103

Modifications reserved

Page 84/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

8.2.2 Parallel UPS shutdown with load transfer on manual bypass Q2

The purpose of this procedure is to supply the

load

directly by

mains

through

manual bypass Q2

This procedure is normally performed when the

System Parallel

must be completely switched OFF for

maintenance or service purpose, performed by an authorised

Service Centre

The

synoptic diagram

, on all UPS units, must display the status

“

LOAD SUPPLIED BY INVERTER

”

1. Disconnect the inverter by pressing

“

Inverter OFF

”

( O ) key and hold until the LED Inverter (7)

turns OFF on all UPS units.

The output will be supplied by the mains through all

automatic

bypass

LEDs Alarm

are lit and the

LEDs Operation

are Off.

The

synoptic diagram

, on all UPS units, must display the status

“

LOAD SUPPLIED BY AUTOMATIC BYPASS

”

2. Close the manual bypass switch Q2 (Pos. I) on all UPS units.

Load

is now supplied from

mains

in parallel from

automatic bypass

and

manual bypass Q2

of all UPS units.

The

synoptic diagram

, on all UPS units, must display the status

“

LOAD SUPPLIED BY AUTOMATIC BYPASS AND MANUAL BYPASS

”

3. Open the output switch Q1 (Pos. 0) on all UPS units.

The

load

is now supplied only through the

manual bypass Q2

The

synoptic diagram

, on all UPS units, must display the status

“

LOAD SUPPLIED BY MANUAL BYPASS Q2

”

4. Press “Total Off” key on all UPS units.

Remove the external battery fuses on each unit

In case of GE battery cabinet:

−

Open fully and remove the cover of fuse-holder by using correctly the handle;

−

Remove the fuses from their place, re-install and close fully the cover of fuse-holder.

The

acoustical alarm

is activated, press

“MUTE”

key to reset it.

Continue

►

Содержание Digital Energy LP 33 Series








































































































Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды

GE Digital Energy LP 33 Series, Руководство по эксплуатации

Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды