GE Digital Energy LP 33 Series Скачать руководство пользователя страница 74

Страница: 74 / 103

Modifications reserved

Page 74/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

8.1.2 UPS shutdown with load transfer on manual bypass Q2

The purpose of this procedure is to supply the

load

directly by

mains

through

manual bypass Q2

This procedure is normally performed when the UPS must be completely switched OFF for maintenance
or service purpose, performed by an authorised

Service Centre

NOTE !

This procedure must not be performed if the UPS is used as

frequency converter

1. Disconnect the inverter by pressing

“

Inverter OFF

”

( O ) key and hold until the LED Inverter (7)

turns OFF.

Load

is transferred to

mains

automatic bypass

LED Alarm

is lit and the

LED Operation

is Off.

The

synoptic diagram

must display the status

“

LOAD SUPPLIED BY

AUTOMATIC BYPASS

”

2. Close the manual bypass switch Q2 (Pos. I).

Load

is now supplied parallel through

automatic bypass

and

manual bypass Q2

The

synoptic diagram

must display the status

“

LOAD SUPPLIED BY

AUTOMATIC BYPASS AND MANUAL BYPASS Q2

”

3. Open the output switch Q1 (Pos. 0).

The

load

is now supplied only through the

manual bypass Q2

The

synoptic diagram

must display the status

“

LOAD SUPPLIED BY

MANUAL BYPASS Q2

”

4. Press “Total Off” key.

5. Remove the external battery fuses.

In case of GE battery cabinet:

−

Open fully and remove the cover of fuse-holder by using correctly the handle;

−

Remove the fuses from their place, re-install and close fully the cover of fuse-holder.

The

acoustical alarm

is activated, press

“MUTE”

key to reset it.

Continue

►

Содержание Digital Energy LP 33 Series








































































































Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды

GE Digital Energy LP 33 Series, Руководство по эксплуатации

Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды