GE Digital Energy LP 33 Series Скачать руководство пользователя страница 61

Страница: 61 / 103

Modifications reserved

Page 61/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

7.3.3 Messages list

Code

Message

Meaning

4111

RECTIFIER MAINS OK

Rectifier input mains is again within the admitted tolerance
(voltage, frequency and phase).

4114

UPS SHUTDOWN

(LOW BATTERY VOLTAGE)

The UPS is in Load OFF status, resulting in Battery supply for
the power supply.
Should the Battery voltage decrease to a value below of the
one set in a parameter, then power supply will shutdown to
avoid damage to the Battery

4119

BATTERY TEST STARTED

Start of manual or automatic battery test.
Rectifier output voltage is decreased to the value defined
by respective parameter.

4120

BATTERY TEST STOPPED

End battery test.
End of manual or automatic battery test.
Rectifier output voltage is restored to floating voltage.

4141

ISMAX DETECTION RECTIFIER

Detection of persistent booster (Is) current limitation.

4161

RECTIFIER ON

Rectifier received the command to switch ON.

4162

RECTIFIER OFF

Rectifier received the command to switch OFF for:
input mains out of tolerance / EPO / UDC max.

4163

GENERATOR ON

Customer Interface (X1 / 11, 22) received a Gen set ON
signalling. Operating mode dependent on setting of
respective parameters.

4164

GENERATOR OFF

Customer Interface (X1 / 11, 22) received a Gen set OFF
signalling. Function bypass enabled dependent on setting
of respective parameter.

4302

INVERTER CANNOT BE

TURNED ON

Inverter cannot be switched on because one of the
following conditions are still present:

Overtemperature

Low battery voltage

Inverter fuses

Overload

K7 opening failure

High battery voltage

DC low

EPO (Emergency Power Off)

4303

INVERTER CANNOT BE

TURNED OFF

Inverter cannot be switched OFF, because the load cannot
be transferred on mains (voltage out of tolerance, not
synchronising, bypass blocked).

4361

INVERTER ON

The command to start the inverter has been activated on
the control panel.

4362

INVERTER OFF

The command to switch OFF the inverter has been done by
the control panel or automatically for alarm detection.

4411

BYPASS MAINS OK

Bypass input mains is again within the admitted tolerance
(voltage, frequency and phase).

4500

COMMAND TOTAL OFF

Disconnection of the load by opening K4, K6 and K7 for:
EPO / Total Off / Overload / Stop operation.

4521

NO BYPASS POWER

With the load supplied by electronic bypass, a mains failure
or K6 opening occurred.

4534

MULTIPLE LOAD TRANSFER

2 transfers inverter-mains have been detected in a short
time, defined by respective parameter (default 30 seconds).

Содержание Digital Energy LP 33 Series








































































































Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды

GE Digital Energy LP 33 Series, Руководство по эксплуатации

Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды