GE Digital Energy LP 33 Series Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 103

background image

Modifications reserved

Page 59/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

Code

Alarm

Meaning

4130

TURN ON RECT.

OR SHUTDOWN UPS

Rectifier and inverter are OFF.
The DC power supply is discharging the battery slowly.
Rectifier must be restarted or battery must be disconnected
in order to avoid damages.

4140

RECTIFIER CONTROL FAILURE

Rectifier voltage hasn’t reached the set value.
Probably fault on regulation loop.
The DC capacitors are not equally charged (more of 50 Vdc
of difference).
The rectifier is switched OFF.

4301

INVERTER FUSES FAILURE

Inverter output fuses blown.
Signalled by electronic detector.
Inverter can be started manually after replacement of
fuses.

4304

K7 CLOSING FAILURE

K7 not closed despite a closing command being done.
Signalled by auxiliary contact.
The load will be supplied by mains.

4305

K7 OPENING FAILURE

K7 not open despite an opening command being done.
Signalled by auxiliary contact.
The load will be supplied by mains.

4312

INV. VOLTAGE OUT

OF TOLERANCE

Inverter output voltage is out of the tolerances defined in
respective parameter (±10%).
Inverter is switched OFF.

4320

ISMAX DETECTION

Detection of inverter bridge (Is) current limitation cause
inverter OFF and automatic restart (message 320).
After 3 times inverter switches OFF for persistent Is max
detection in time.
Inverter switch OFF, and it can be restarted manually.

4340

INVERTER CONTROL FAILURE

The slave oscillator is not synchronised with the master,
thus causing the shutdown of it’s inverter.

4347

OSCILLATOR FAILURE

Auto calibration of the Inverters freerun frequency was not
possible.
The oscillator frequency of this unit is out of tolerance.

4402

RECTIFIER CANNOT BE

TURNED ON

The rectifier cannot be turned on because the DC link
voltage has not reached the requested value.

4404

K6 CLOSING FAILURE

K6 not closed despite a closing command being done.
Signalled by auxiliary contact.
The load cannot be supplied by electronic bypass.

4405

K6 OPENING FAILURE

K6 not open despite an opening command being done.
Signalled by auxiliary contact.

4410

BYPASS MAINS OUT

OF TOLERANCE

The mains bypass voltage is out of the tolerances (±10%).
K6 opens, synchronisation with mains is inhibited and
transfer to mains is blocked.

4520

NO INVERTER POWER

The load supplied by utility is over 100%.
The load remains blocked on utility as long as alarm
overload is active.

4530

LOAD LOCKED ON MAINS

Load is locked on mains because 3 transfers on mains have
been detected in a short time (default 30 seconds).
Transfer will be free again after a time defined by
respective parameter (default 30 seconds).

«
...
57
58
59
60
61
...
»

Содержание Digital Energy LP 33 Series








































































































Отзывы:

Нет отзывов

Похожие инструкции для Digital Energy LP 33 Series

Бренд: Campbell Hausfeld Страницы: 24

Бренд: Campbell Hausfeld Страницы: 12

Бренд: hager Страницы: 2

Bomag BPR 70/70 D

Бренд: Fayat Group Страницы: 74

Бренд: Fayat Страницы: 110

Bomag BPR 25/40

Бренд: Fayat Страницы: 57

Бренд: Xaoc Devices Страницы: 8

Бренд: T-Drill Страницы: 49

Бренд: Landoll Страницы: 54

Бренд: TMG Страницы: 19

Бренд: Parkside Страницы: 37

Бренд: Far Tools Страницы: 30

Бренд: Hama Страницы: 29

SMP10C12X Series

Бренд: Altronix Страницы: 8

Бренд: OKUtools Страницы: 18

Бренд: BK Precision Страницы: 42

Бренд: Berker Страницы: 2

Бренд: Draper Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды