GE Digital Energy LP 33 Series Скачать руководство пользователя страница 77

Страница: 77 / 103

Modifications reserved

Page 77/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

8.1.4 Complete UPS shutdown

As a result of this procedure the UPS is completely switched OFF and not powered.

NOTE !

Follow this procedure only in case the UPS system and the load must be completely
powered-down.

1. Press “Total Off” key.

Open the output switch Q1 (Pos. 0).

3. Remove the external battery fuses

In case of GE battery cabinet:

−

Open fully and remove the cover of fuse-holder by using correctly the handle;

−

Remove the fuses from their place, re-install and close fully the cover of fuse-holder.

The

acoustical alarm

is activated, press

“MUTE”

key to reset it.

In order to discharge the DC link capacitors, insert the inverter by pressing

“

Inverter ON

”

( I ) key.

Home\Meter

INVERTER

f :

50.0

L1 :

L2 :

L3 :

T :

SYNCHRONISED

Remark

Command

INVERTER ON

will be enabled only when the inverter

voltage of each phase decreases below

7 Vac

(about 30 seconds).

The

acoustical alarm

is activated, press

“MUTE”

key (from Home

screen) to reset it.

Home\Meter

BOOSTER

f :

50.0

L1 :

397

L2 :

395

L3 :

393

Vp :

Vn :

Before proceeding to step

, check on the display panel that the

link voltage

(both polarities)

and

has reached the max.

voltage of

5 Vdc

(about 30 seconds).

5. Disconnect the inverter by pressing

“

Inverter OFF

”

( O ) key and hold until the LED Inverter (7)

turns OFF.

Switch OFF the mains power at the AC input distribution panel.

END OF PROCEDURE

WARNING !

If the above procedure is not completely performed, it could cause
serious damages to the UPS.
In case the procedure described on step

“4 - Discharge DC link capacitors”

cannot

be completely performed, the DC capacitors could be charged with dangerous
voltage for min.5 minutes.
Wait until capacitors are completely discharged before starting the UPS again.
Apart from the front door, do not open any other part of the UPS.

Содержание Digital Energy LP 33 Series








































































































Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды

GE Digital Energy LP 33 Series, Руководство по эксплуатации

Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды