GE Digital Energy LP 33 Series Скачать руководство пользователя страница 67

Страница: 67 / 103

Modifications reserved

Page 67/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

To better understand the

ECO Mode

programming modes, some typical examples are shown:

Example 1

For continuous

ECO Mode

set the

ECO Mode START

times to 00:00

and the

ECO Mode STOP

times to

23:59

for all weekdays, but almost

1 day must have 1 minute of

VFI

programmation: i.e

d2 - Sunday

00:00 to 23:58).

Weekday

- Saturday

- Sunday

- Monday

- Tuesday

- Wednesday

- Thursday

- Friday

ECO Mode START

00:00 00:00 00:00 00:00 00:00 00:00 00:00

ECO Mode STOP

23:59 23:58 23:59 23:59 23:59 23:59 23:59

Example 2

ECO Mode STOP

before

ECO Mode START

ECO Mode START

18:00,

ECO Mode STOP

06:00 for weekday

d4 - Tuesday

Means that on

d4 - Tuesday

the

ECO Mode

is active between 00:00 and 06:00 and between 18:00 and

23:59.

Weekday

- Saturday

- Sunday

- Monday

- Tuesday

- Wednesday

- Thursday

- Friday

ECO Mode START

00:00 00:00 00:00 18:00 00:00 00:00 00:00

ECO Mode STOP

23:59 23:59 23:59 06:00 23:59 23:59 23:59

Example 3

ECO Mode

during the night and week-end.

If the

ECO Mode

must be enabled all nights (

d3 - Monday

d7 - Friday

) between 18:00 in the evening

and 06:00 of the following morning and during all Saturday (

) and Sunday (

), the corresponding

parameters are:

Weekday

- Saturday

- Sunday

- Monday

- Tuesday

- Wednesday

- Thursday

- Friday

ECO Mode START

00:00 00:00 18:00 18:00 18:00 18:00 18:00

ECO Mode STOP

23:59 23:59 06:00 06:00 06:00 06:00 06:00

Example 4

If the

ECO Mode

must be enabled on

Monday

(

)

and

Tuesday

(

)

between 18:00 in the evening and

06:00 of the following morning, on

Friday

(

)

between 12:00 and 13:00, during all

Saturday

(

)

and on

Sunday

(

)

until 20:00, the corresponding parameters are.

Weekday

- Saturday

- Sunday

- Monday

- Tuesday

- Wednesday

- Thursday

- Friday

ECO Mode START

00:00 00:00 18:00 18:00 00:00 00:00 12:00

ECO Mode STOP

23:59 20:00 23:59 06:00 06:00 00:00 13:00

ECO Mode START

ECO Mode STOP

In dark colour are displayed the times with

ECO Mode

operation.

The arrows indicate the conditions given by the

ECO Mode START

and

ECO Mode STOP

times introduced

with the parameters.

Note that on day

d6 - Thursday

the interval has length 0 (zero), therefore the

ECO Mode

is not enabled

on this day.

Содержание Digital Energy LP 33 Series








































































































Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

GE Digital Energy LP 33 Series, Руководство по эксплуатации, Страница: 67 / 103

Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы: