GE Digital Energy LP 33 Series Скачать руководство пользователя страница 19

Страница: 19 / 103

Modifications reserved

Page 19/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

4.4 UPS PARALLELED ON THE SAME BATTERY

NOTE !

Parallel System

with a

Common Battery

for two or more

UPS

, requires a particular

installation and adequate setting of some parameters, (accessible only through
password), and can therefore only be done by a qualified GE engineer.

Usually each

UPS Unit

runs with its own

Battery

In case of parallel units running with a

Common Battery

(max. 4 UPS - see

Fig. 4.4-1

), the sharing circuit

between the individual

UPS

is integrated in the communication bus of the system in order to assure an

equal sharing of the

Rectifiers

output currents.

Fig. 4.4-1 Diagram RPA system with UPS on common battery

1 –

2 –

3 –

4 –

5 –

6 –

7 –

8 –

Rectifier

Inverter

Automatic Bypass

Manual Bypass

Mains Power

Load Bus Bar

External Battery Fuse

Battery

Pay attention to the following recommendations:

•

The units delivered for this functioning mode needs a special parameters setting, so they must be
prepared in advance before the installation.

•

The installation must be performed only with the UPS system completely shut down.

•

The AC

Rectifiers

input power (5) must be the same, with clockwise phase rotation for each unit.

•

Each

Rectifier

must be set for the same floating DC voltage and the same

Battery

current limitation.

•

It is mandatory to install the fuses /

MCB

(7) on each line connecting the

Rectifiers

to the common

Battery

for maintenance / safety reasons (see

Section 5.7.2

•

In case a unit must be powered down for maintenance, switch-OFF the concerned unit before open
the DC fuses /

MCB

on the

Battery

line (7).

•

It is recommended to connect an external NO free contact

“Battery Fuses”

to the UPS and to enable

the function by setting the parameter (see

Section 9.1

•

If an emergency generator set supplies the UPS, and the free contact

“Generator ON”

is connected

to the

Customer Interface

, connect a separate NO free contact on each parallel unit.

•

The parameters enabling the

Battery test

, both manual and automatic, must be set in the same

mode on all the units sharing a

Common Battery

•

Do not connect the temperature sensor for automatic

battery floating voltage

compensation.

•

Do not enable the function

Boost charge

Содержание Digital Energy LP 33 Series








































































































Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды

GE Digital Energy LP 33 Series, Руководство по эксплуатации

Результаты поиска

Содержание Digital Energy LP 33 Series

Отзывы:

Похожие инструкции для Digital Energy LP 33 Series

Бренды по названию

Популярные бренды