GE CyberDome Series Скачать руководство пользователя страница 9

Страница: 9 / 52

CyberDome Series Installation Manual

Housing Installation

A06-8SG0/B/April2006/1033921C

For installation, proceed as follows:

CAUTION!

DO NOT provide power to the housing until all installation steps are complete.

Step 1)

Determine where the CyberDome is to be located and remove the ceiling panel at
that location.

Step 2)

If the removed ceiling panel is the smaller 24 in. x 24 in. (60.96 cm x 60.96 cm)
size, continue with step 3.

If the panel is the larger 24 in. x 48 in. (60.96 cm x 121.92 cm) size, cut the panel
into two 24 in. x 24 in. (60.96 cm x 60.96 cm) sections and install a 24 in.
(60.96 cm) T-bar across the center of the ceiling opening. Refer to

Appendix A:

KTA-24-6 and KTA-24-8/KTA-10-8 T-Bar Support Kits

. See

Figure

Step 3)

Feed the video, 24VAC, and RS422 control cables through the ceiling to the
vacated panel location.

Step 4)

Prepare the cables as shown in

Figure 6.

Step 5)

Attach the CyberDome housing to the KTA-22-6 panel using the three 10-32
flathead screws provided.

Step 6)

Place the housing/panel assembly in the ceiling.

CAUTION!

Each safety cable in step 7 (below) must be able to support a 35 lb (15.88 kg) load.

Step 7)

Attach two metal safety cables between the KTA-22-6 and the ceiling’s super-
structure to insure that the mounting panel cannot fall. See

Figure 7

. Holes are

located in each side of the panel for this purpose.

Figure 6: Preparing the Cables

Figure 7: Attaching the Safety Cables

Содержание CyberDome Series





















































Результаты поиска

Содержание CyberDome Series

Отзывы:

GE CyberDome Series, Руководство по установке, Страница: 9 / 52

Результаты поиска

Содержание CyberDome Series

Отзывы: