GE CyberDome Series Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 52

GE CyberDome Series Скачать руководство пользователя страница 39

CyberDome Series Installation Manual

Appendix A: Accessory Installation

39

A06-8SG0/B/April2006/1033921C

KTP-24-8 Multiple Output Power Supply

The KTP-24-8 is a compact and durable power supply that provides eight isolated 24VAC
outputs for indoor applications. Each output can power devices requiring 1 amp or less. The
unit is equipped with automatic resettable fuses for each output and is powered from a stan-
dard 115 or 230VAC source.

CAUTION!

The KTP-24-8 was designed for indoor applications only. For outdoor units with a heater/fan, use
the KTP-24 Outdoor Power Supply.

Note:

The KTP-24-8 can also be mounted in a rack using the KTP-24-00 Rack Mount Kit accessory.

Step 1)

Mount the unit using the slots provided.

Step 2)

Make cable connections to the KTP-24-8 as shown in

Figure 58

. Refer to

Table 1

(page 6) for suitable cable gauge sizes when connecting the output cables.

Operation

Each 24VAC output of the power supply has a resettable fuse that will trip if the current draw
exceeds one amp. In this event, the device on that output may operate intermittently, or not at
all. The fuse will automatically reset itself when the load is removed from the output.

CAUTION!

DO NOT reconnect any device that caused an output fuse to trip, until the device has been inspected
and determined to be in proper working condition.

Figure 58: KTP-24-8 Cable Connections

«
...
37
38
39
40
41
...
»

Содержание CyberDome Series





















































Отзывы:

Нет отзывов