GE CyberDome Series Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 52

GE CyberDome Series Скачать руководство пользователя страница 28

Housing Installation

CyberDome Series Installation Manual

28

A06-8SG0/B/April2006/1033921C

Heavy-duty Housing (CyberDome HD) Installation

The CyberDome HD is enclosed in a tamper-resistant aluminum housing with an impact-
resistant acrylic dome. Attached to the housing is a reinforced swivel-mount bracket. It is
designed to mount against a hard surface, but will also mate with a KTA-25/KTA-25W Corner-
mount Bracket or a KTA-26/KTA-26W Pole-mount Bracket. For instructions on using the
corner- or pole-mount brackets, refer to

Appendix A: Accessory Installation

.

CAUTION!

DO NOT provide power to the housing until all installation steps are complete.

To install and mount the CyberDome HD directly to a hard surface (such as concrete), pro-
ceed with the following steps:

Step 1)

Locate the carriage bolts that secure the upper housing to the swivel-mount
bracket. See

Figure 42

. Loosen and remove the ESNA nuts (inside the upper

housing), remove the carriage bolts, and detach the upper housing.

CAUTION!

DO NOT mount the heavy-duty CyberDome HD via the small mounting holes alone. They are for
additional security where needed.

Step 2)

Using the swivel-mount bracket as a template, mark the mounting surface where
the CyberDome HD is to be installed. See

Figure 43

. Mark the four large mount-

ing slots. For additional security, also mark the four small mounting holes.

Step 3)

Drill the four (or eight) holes into the mounting surface.

Figure 42: Removing the Carriage Bolts

«
...
26
27
28
29
30
...
»

Содержание CyberDome Series





















































Отзывы:

Нет отзывов