GE CyberDome Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 52

GE CyberDome Series Скачать руководство пользователя страница 11

CyberDome Series Installation Manual

Housing Installation

11

A06-8SG0/B/April2006/1033921C

Figure 10: Fastener Hole Locations

To install the upper housing using the KTA-23-6 Ceiling Ring, proceed with the following steps:

CAUTION!

DO NOT provide power to the housing until all installation steps are complete.

Figure 9: Minimum Ceiling Strength

Method 2: Installation Into A Non-Removable False Ceiling

Note:

This method of installation should be used only when the false ceiling is sturdy enough to support
the weight of a complete CyberDome assembly.

The KTA-23-6 Ceiling Ring (formerly the KTA-01-6) is used to install the flush-mount housing
in a non-removable type false ceiling. The ring allows installation by a single person and does
not require that the person enter the ceiling cavity (except for cable routing).

CAUTION!

The KTA-23-6 distributes the weight of the CyberDome around the perimeter of the ceiling cutout.
The ceiling must be strong enough to support a minimum of 35 lb (15.88 kg), as illustrated in

Figure 9

.

Step 1)

Hold the ceiling ring in the de-
sired location on the ceiling with
the flat surface facing away from
the ceiling.

Step 2)

Use a pencil to trace the inside
of the ceiling ring and to mark
all five fastener hole locations (as
shown in

Figure 10

).

«
...
9
10
11
12
13
...
»

Содержание CyberDome Series





















































Отзывы:

Нет отзывов