GE CyberDome Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 52

GE CyberDome Series Скачать руководство пользователя страница 35

CyberDome Series Installation Manual

PTZ and Dome Installation

35

A06-8SG0/B/April2006/1033921C

To attach the dome assembly to the heavy-duty CyberDome housing:

Step 1)

Fasten the dome safety cable to the upper housing with the safety clip. See

Figure 52

.

Step 2)

Locate the mounting tabs on the dome plate and insert them into the mounting
slots on the upper housing.

Step 3)

Lock the dome in place with the keylock latch.

Installation is now complete.

Programming and Operating the CyberDome

Note:

To ensure that unit(s) are operating properly, test the pan, tilt and lens functions once each week.

CyberDomes come equipped with a variety of camera options and each camera’s program-
ming varies depending on available functions. Refer to the

CyberDome Programming Instruc-

tions

manual for programming instructions for any CyberDome.

CyberDomes are controlled from either of GE Security’s KTD-404/304 or KTD-400/300 con-
troller keypads. Refer to the corresponding keypad manual for instructions on operating all
CyberDomes.

«
...
33
34
35
36
37
...
»

Содержание CyberDome Series





















































Отзывы:

Нет отзывов