GE CyberDome Series Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 52

GE CyberDome Series Скачать руководство пользователя страница 40

Appendix A: Accessory Installation

CyberDome Series Installation Manual

40

A06-8SG0/B/April2006/1033921C

KTA-27/KTA-27W Roof-mount Adapter

The KTA-27/KTA-27W Roof-mount Adapter (formerly KTA-09-12) is designed to combine with
the KTA-02-12W Wall-mount Bracket or KTA-20/KTA-20T CyberMount on the roof or parapet
of a building. The Roof-mount Adapter is hinged to allow the CyberDome to pivot over the roof
for safe servicing.

Step 1)

Remove the cover screw from the top of the KTA-27/KTA-27W and open the
bracket. See

Figure 59

.

Step 2)

Locate the six mounting slots on the base of the bracket. See

Figures 59

and

60

.

Step 3)

Place the Roof-mount Adapter on the edge of the roof or parapet, and mark the
location of the mounting slots. See

Figures 59

and

60

.

Step 4)

Prepare the mounting slots in accordance with the type of wall (e.g., concrete,
wood) and fasteners used.

CAUTION!

For safety, the hardware and procedure used for securing the KTA-27/27W must allow it to support
a minimum of a 35 lb (15.88 kg) load.

Step 5)

Secure the adapter to the roof or parapet with the appropriate fasteners.

Step 6)

Properly seal all mounting holes that could cause leaks into the roof structure.

Figure 59. Roof-mount Adapter Installation

Figure 60. Base of Roof-mount Adapter

«
...
38
39
40
41
42
...
»

Содержание CyberDome Series





















































Отзывы:

Нет отзывов