GE CyberDome Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 52

GE CyberDome Series Скачать руководство пользователя страница 6

6

Introduction

CyberDome Series Installation Manual

A06-8SG0/B/April2006/1033921C

Cable Requirements

For operation, CyberDomes require video, power and data cables as described below:
1) The video cable carries the video signal to the remote viewing site. If sending video via

coaxial cable, a 75-ohm coaxial cable is typically used. If sending video via twisted-pair
cable, an unshielded, 22 gauge (0.64 mm) twisted-pair cable is needed.

2) The 24VAC cable powers the CyberDome and the camera. To determine cable size, refer

to the

Power Cable Size and Length

subsection of the

Introduction

.

3) The RS422 control cable carries commands from the Digiplex keypad to the CyberDome.

An unshielded, two-conductor, twisted-pair cable is required. Recommended cable size
is 22 gauge (0.64 mm).

NOTE: When using the UTP interface modules, the unshielded twisted-pair video and RS422 control
wires can share the same wire jacket, but must remain as separate twisted pairs.

Power Requirements

CAUTION!

For optimal video performance, all CyberDomes must be powered from an

isolated

24 VAC power

source—fused outputs are

not

adequate. Allowable voltage range is 20 to 28 volts.

All domes require a 24VAC power supply that provides isolated outputs to operate the domes’
pan/tilt drive, camera, and optional heater/fan (E Option). The total power requirement varies
depending on the model of the CyberDome.

Dome power requirements (at 24 VAC):

•

All domes without a heater/fan require 16 VA

•

7-inch domes with heater/fan require 51 VA

•

Heavy-duty domes with heater/fan require 68 VA.

Power Cable Size and Length

It is important to choose the proper gauge of the cable that supplies 24 volts to the CyberDome.
An inadequate gauge will cause a voltage drop resulting in improper operation.

Table 1 gives the recommended cable lengths of varying wire gauges for a CyberDome with a
color camera. Note that the heater and fan (E Option) reduces maximum cable length sub-
stantially.

Table 1. Recommended maximum cable lengths.

Maximum Cable Length

Wire Gauge

All Domes

without Heater/Fan

(16VA)

7-inch Domes

with Heater/Fan

(51VA)

Heavy-duty Domes

with Heater/Fan

(91VA)

(awg)

(mm

2

)

Feet

Meters

Feet

Meters

Feet

Meters

10

2.60

3000

915

900

274

630

192

12

2.05

1900

580

570

174

400

122

14

1.62

1200

365

360

110

250

76

16

1.29

750

230

230

70

160

49

18

1.02

465

142

145

44

100

30

20

0.81

290

90

90

27

62

19

22

0.64

185

56

60

18

40

12

«
...
4
5
6
7
8
...
»

Содержание CyberDome Series





















































Отзывы:

Нет отзывов