GE CyberDome Series Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 52

GE CyberDome Series Скачать руководство пользователя страница 41

CyberDome Series Installation Manual

Appendix A: Accessory Installation

41

A06-8SG0/B/April2006/1033921C

Step 7)

Route the power, RS422, and video cables through the KTA-09-12, leaving enough
cable to attach the cables to the inside of the roof-mount adapter and continue
them through the KTA-02-12W and into the camera housing.

Step 8)

Attach the KTA-02-12W Wall-mount Bracket to the roof-mount adapter. See

Fig-

ure 59

.

Step 9)

Attach the pendant-mount housing to the KTA-02-12W according to the instruc-
tions given on page 49.

Step 10)

Close the KTA-09-12 and secure it with the cover screw.

KTA-24-6 and KTA-10-8 T-bar Support Kits

The KTA-24-6 and KTA-10-8 are T-bar support kits for mounting one KTA-series flush-mount
dome in an existing ceiling panel. KTA-24-6 is for 6-inch flush-mount housings and KTA-10-8
is for 8-inch flush-mount housings. The T-bar support kit distributes the weight of the dome to
the panel braces via support brackets. Each kit comes with one ceiling ring and mounting
hardware.

Step 1)

Remove the T-bar ceiling panel.

Step 2)

Hold the ceiling ring in the desired location on the tile with the flat surface facing
away from the panel.

Step 3)

Use a pencil to trace the inside of the ceiling ring and to mark all five fastener hole
locations (as shown in

Figure 11

on page 11).

Step 4)

Using a

3

⁄

16

” drill bit, drill all five fastener holes. Be certain that all holes are drilled

perpendicular to the panel.

Step 5)

Cut a hole in the panel using the penciled outline as a guide.

Step 6)

Place the T-bar support brackets flush against the inside of the panel, with the
long sides flat and the short sides vertical. Align the mounting holes with the
drilled holes in the panel. See

Figure 61

.

Figure 61: Installing the T-bar Support Kit with Ceiling Ring

«
...
39
40
41
42
43
...
»

Содержание CyberDome Series





















































Отзывы:

Нет отзывов