GE CyberDome Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 52

GE CyberDome Series Скачать руководство пользователя страница 10

Housing Installation

CyberDome Series Installation Manual

10

A06-8SG0/B/April2006/1033921C

CAUTION!

DO NOT connect the 24VAC power cable to the video or RS422 connection in step 8 (below), or the
CyberDome will be damaged.

Step 8)

Connect the prepared cables to the interface module. See

Figure 8

.

There are two versions of the CyberDome interface module depending on whether
video is being sent via coaxial cable (CyberDome Coaxial Interface Module) or
unshielded twisted-pair wire (CyberDome UTP Interface Module).

NOTE: When using the CyberDome UTP Interface Module, the unshielded twisted-
pair video and RS422 control wires can share the same wire jacket, but must remain
as separate twisted pairs.

Step 9)

Insert the interconnect cable from the CyberDome into the RJ45 jack in the inter-
face module. See

Figure 8

.

Figure 8: Connecting the Cables to Either CyberDome Interface Module

Step 10)

Reinstall any removed ceiling panels.

Step 11)

Proceed to

RS422 Termination

on page 31.

«
...
8
9
10
11
12
...
»

Содержание CyberDome Series





















































Отзывы:

Нет отзывов