GE CyberDome Series Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 52

GE CyberDome Series Скачать руководство пользователя страница 37

CyberDome Series Installation Manual

Appendix A: Accessory Installation

37

A06-8SG0/B/April2006/1033921C

APPENDIX A: ACCESSORY INSTALLATION

KTA-25/KTA-25W Corner Adapter

The KTA-25/KTA-25W Corner-mount Bracket (formerly KTA-06-12) is used to mount a
KTA-02-12W Wall-mount Bracket or KTA-20/KTA-20T CyberMount to the corner of a building.
See

Figure 53

.

CAUTION!

For safety, the hardware and procedure used for securing the KTA-25/25W must allow it to support
a minimum of a 35 lb (15.88 kg) load.

KTA-26/KTA-26W Pole Adapter

The KTA-26/KTA-26W Pole-mount Bracket (formerly KTA-07-12) is used to adapt a KTA-02-12W
Wall-mount Bracket or KTA-20/KTA-20T CyberMount to a pole. The bracket can be bolted to
the pole or secured with adjustable stainless-steel bands. See

Figure 54

.

CAUTION!

For safety, the hardware and procedure used for securing the KTA-26/26W must allow it to support
a minimum of a 35 lb (15.88 kg) load.

Figure 54: Pole Adapter Installation

Figure 53: Corner Adapter Installation

Step 1)

Place the adapter on the corner
of the building and mark the lo-
cation of the four mounting holes.
See

Figure 53

.

Step 2)

Prepare the four mounting holes
in accordance with the type of
wall (e.g., concrete, wood) and
fasteners used.

Step 3)

Secure the adapter to the wall
with the appropriate fasteners.

Step 4)

Attach the KTA-02-12W Wall
Bracket to the adapter using the
hardware provided.

«
...
35
36
37
38
39
...
»

Содержание CyberDome Series





















































Отзывы:

Нет отзывов