manualshive.com logo in svg

GE CyberDome Series, Руководство по установке, Страница: 24 / 52

Поделиться
Скачать
GE CyberDome Series Скачать руководство пользователя страница 24

Housing Installation

CyberDome Series Installation Manual

24

A06-8SG0/B/April2006/1033921C

CAUTION!

DO NOT connect the 24VAC power cable to the video or RS422 connection in step 12 (below), or the
CyberDome will be damaged.

Step 12)

Attach the interface connector card (provided with the CyberDome) to the cable
assembly. See 

Figure 36

.

There are two versions of the CyberDome interface module depending on whether
video is being sent via coaxial cable (CyberDome Coaxial Interface Module) or
unshielded twisted-pair wire (CyberDome UTP Interface Module).

NOTE: When using the CyberDome UTP Interface Module, the unshielded twisted-
pair video and RS422 control wires can share the same wire jacket, but must remain
as separate twisted pairs.

Step 13)

Bring the housing near the end of the swing arm and insert the CyberDome’s
interconnect cable into the RJ45 jack on the interface module. See 

Figure 36

.

Step 14)

If installing the optional heater/fan (E Option), also connect the heater’s power
cable to the 2-pin Molex connector on the module. See 

Figure 36

.

The fan assembly is attached separately inside the housing to the PTZ assem-
bly. Refer to 

E Option (Heater/Fan)

 in 

Appendix A

.

Figure 36. Swing Mount Connections to Either CyberDome Interface Module

Содержание CyberDome Series





















































Отзывы:

Нет отзывов