GE CyberDome Series Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 52

GE CyberDome Series Скачать руководство пользователя страница 4

4

Preface

CyberDome Series Installation Manual

A06-8SG0/B/April2006/1033921C

PREFACE

This document includes an overview of the product and detailed instructions explaining how to
install and operate the unit. There is also information describing how to contact technical
support if you have questions or concerns.

To use this document effectively, you should have the following minimum qualifications:

•

a basic knowledge of CCTV systems and components; and

•

a basic knowledge of electrical wiring and low-voltage electrical hookups.

Read these instructions and all ancillary documentation entirely before installing or operating
this product. The most current versions of this and related documentation may be found on
our website.

NOTE:

A qualified service person, complying with all applicable codes, should perform all

required hardware installation.

These terms may appear in this manual:

WARNING:

Improper use of this equipment can cause severe bodily injury or equipment damage.

CAUTION:

Improper use of this equipment can cause equipment damage.

NOTE:

Notes contain important information about a product or procedure.

* This symbol indicates electrical warnings and cautions.

** This symbol indicates general warnings and cautions.

*

**

«
...
2
3
4
5
6
...
»

Содержание CyberDome Series





















































Отзывы:

Нет отзывов