Fujitsu MHZ2080BJ Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 320

background image

Interface

5.2.4 Shadow block registers

(1) Error

Field

The Error Field indicates the status of the command executed by the device.
The fields are valid when the ERR bit of the Status field is 1.

This register contains a diagnostic code after power is turned on, the COMRESET
or the EXECUTIVE DEVICE DIAGNOSTIC command is executed.

•

[Status at the completion of command execution other than diagnostic command]

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

X UNC X IDNF/

SFRW

SFRR

ABRT

TK0NF

AMNF

X: Unused

- Bit 7:

Unused

- Bit 6:

Uncorrectable Data Error (UNC). This bit indicates that an
uncorrectable data error has been encountered.

- Bit 5:

Unused

- Bit 4:

ID Not Found (IDNF). This bit indicates an error except for bad sector,
uncorrectable error and SB not found.

Or, SATA Frame Error Write (SFRW) This bit indicates that a SATA
communication error has been encountered during the write process.
In this case, bit4 and bit2 are set both.

- Bit 3:

SATA Frame Error Read (SF RR). This bit indicates that a SATA
communication error has been encountered during the read process.
In this case, bit3 and bit2 are set both.

- Bit 2:

Aborted Command (ABRT). This bit indicates that the requested
command was aborted due to a device status error (e.g. Not Ready,
Write Fault) or the command code was invalid.

- Bit 1:

Track 0 Not Found (TK0NF). This bit indicates that track 0 was not
found during RECALIBRATE command execution.

- Bit 0:

Address Mark Not Found (AMNF). This bit indicates that the SB Not
Found error occurred.

[Diagnostic code]

- X '00': Format Unit is not completed.

- X '01': No Error Detected.

- X '02': HDC Diagnostic Error

- X '03': Data Buffer Diagnostic Error

- X '04': Memory Diagnostic Error

- X '05': Reading the system area is abnormal.

- X '06': Calibration is abnormal.

5-22

C141-E280

«
...
94
95
96
97
98
...
»

Содержание MHZ2080BJ

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHZ2080BJ

Бренд: IBM Страницы: 2

Бренд: WiebeTech Страницы: 4

Бренд: IBM Страницы: 78

DiskCrypt Mobile DCM300

Бренд: DigiSAFE Страницы: 27

Бренд: IBM Страницы: 2

SmartStore SM2015

Бренд: Riverlea Страницы: 16

Бренд: Far Tools Страницы: 10

Бренд: CalDigit Страницы: 16

Бренд: U.S. General Страницы: 2

Бренд: morse Страницы: 4

Digi Drive Movie

Бренд: Teac Страницы: 9

Бренд: WilTec Страницы: 3

Бренд: Digital Equipment Страницы: 70

Бренд: ClearSpan Страницы: 27

Бренд: Habey Страницы: 4

Бренд: Sunpal Страницы: 3

Бренд: Kaysun Страницы: 52

Бренд: Costway Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды