Fujitsu MHZ2080BJ Скачать руководство пользователя страница 147

Страница: 147 / 320

5.3 Host Commands

Table 5.24 Format of SCT STATUS Response (1/2)

Byte(hex) Contents

00, 01

Format Version

02, 03

SCT Version

04, 05

SCT Spec

06 to 09

Status Flag

Bit31-1: Reserved

Bit0: Initialized flag (maintained Power-OFF/ON)

0 = When any user LBA is written, this bit is cleared.

This bit is also cleared if the capacity of the drive is changed via
SET MAX (EXT), DCO.

1= A WRITE SAME command to all logical blocks has completed

without error.

Drive State

00h = Active

01h = not support (Standby).

02h = not support (Sleep).

03h = DST executing in background

04h = SMART Off-line Data collection executing in background

05h = SCT command executing in background

06h-FFh = Reserved

0B to 0D

Reserved

0E, 0F

Extended Status Code

Status of last SCT command issued

* (See Table 5.25)

10, 11

Action Code

Action code of last SCT command issued

12, 13

Function Code

Function code of last SCT command issued

C141-E280

5-73

Содержание MHZ2080BJ

































































































































































































































































































































Результаты поиска

Содержание MHZ2080BJ

Отзывы:

Fujitsu MHZ2080BJ, Руководство по эксплуатации/техническому обслуживанию, Страница: 147 / 320

Результаты поиска

Содержание MHZ2080BJ

Отзывы: