manualshive.com logo in svg

Fujitsu MHZ2080BJ, Руководство по эксплуатации/техническому обслуживанию

Fujitsu MHZ2080BJ - продуктовое / техническое руководство по обслуживанию. Вы можете скачать это бесплатное руководство на нашем сайте. Получите доступ к подробной информации о продукте, необходимой для правильного обслуживания и ухода за ним.Скачайте руководство на manualshive.com.

Поделиться
Скачать
background image

Operations

 

• 

SET ADDRESS MAX (EXT) 

The maximum LBA specified in SET MAX ADDRESS or SET MAX 
ADDRESS EXT. 

• 

SET FEATURES (Write Cache Enable/Disable) 

The write cache enable/disable setting established by the SET FEATURES 
command with subcommand code of 02h or 82h. 

• 

SET FEATURES (Set Transfer Mode) 

PIO, Multiword, and UDMA transfer mode settings established by the SET 
FEATURES command with subcommand code of 03h. 

• 

SET FEATURES (Advanced Power Management Enable/Disable) 

The advanced power management enable/disable setting established by the 
SET FEATURES command with subcommand code of 05h or 85h. The 
advanced power management level established in the Sector Count field when 
advanced power management is enabled (SET FEATURES subcommand 
code 05h) shall also be preserved. 

• 

SET FEATURES (Read Look-Ahead) 

The read look-ahead enable/disable setting established by the SET 
FEATURES command with subcommand code of 55h or AAh. 

• 

SET MULTIPLE MODE 

The block size established with the SET MULTIPLE MODE command. 

• 

SET FEATURES (Write-Read-Verify feature set) 

The Write-Read-Verify enable/disable setting established by the SET 
FEATURES command with subcommand code of 0b h/8b h. 

6-6 

C141-E280 

Содержание MHZ2080BJ

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHZ2080BJ

R/Evolution 2000 Series Getting Started Manual preview
2000 Series
Бренд: R/Evolution Страницы: 58
Gardiun Cambridge Instruction Manual preview
Cambridge
Бренд: Gardiun Страницы: 27
LaCie 301160U - 1TB Ethernet Disk RAID Network Attached... Quick Install Manual preview
301160U - 1TB Ethernet Disk RAID Network Attached...
Бренд: LaCie Страницы: 5
LaCie 301382U Specifications preview
301382U
Бренд: LaCie Страницы: 6
Elementia Materials Plycem Eureka Tank Installation Manual preview
Plycem Eureka Tank
Бренд: Elementia Materials Страницы: 6
Qualstar RLS-4470 Technical & Service Manual preview
RLS-4470
Бренд: Qualstar Страницы: 205
Salsbury Industries 18-51000 Series Installation Instructions preview
18-51000 Series
Бренд: Salsbury Industries Страницы: 5
IBM SAN64B-6 Installation, Service And User Manual preview
SAN64B-6
Бренд: IBM Страницы: 122
IBM Travelstar 14GS Quick Installation Manual preview
Travelstar 14GS
Бренд: IBM Страницы: 2
Hanover HGS001 Series Assembly & Care Manual preview
HGS001 Series
Бренд: Hanover Страницы: 12
kincrome Evolution K7916 Operation Manual preview
Evolution K7916
Бренд: kincrome Страницы: 2
Raidon iT4300 Series Quick Installation Manual preview
iT4300 Series
Бренд: Raidon Страницы: 2
QNAP TS-h2483XU-RP Series Quick Installation Manual preview
TS-h2483XU-RP Series
Бренд: QNAP Страницы: 12
Sony MS-EX1G Operating Instructions preview
MS-EX1G
Бренд: Sony Страницы: 2
Verbatim tuff-'n'-tiny Quick Manual preview
tuff-'n'-tiny
Бренд: Verbatim Страницы: 15
DANE-ELEC SOEXTREME SUPERSPEED Datasheet preview
SOEXTREME SUPERSPEED
Бренд: DANE-ELEC Страницы: 1
TerraMaster TNAS F5-420 Fundamentals And Preliminaries preview
TNAS F5-420
Бренд: TerraMaster Страницы: 13
Costway HW65477WH User Manual preview
HW65477WH
Бренд: Costway Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды