Fujitsu MHZ2080BJ Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 320

background image

Interface

(3)

WRITE SECTOR(S) (X '30' or X '31')

This command writes data of sectors from the address specified in the
Device/Head, Cylinder High, Cylinder Low, and Sector Number fields to the
address specified in the Sector Count field. Number of sectors can be specified
from 1 to 256 sectors. A sector count of 0 requests 256 sectors. Data transfer
begins at the sector specified in the Sector Number field. For the protocols related
to data transfer, see Subsection 5.4.3.

If the head is not on the track specified by the host, the device performs an implied
seek. After the head reaches to the specified track, the device writes the target
sector.

If an error occurs when writing to the target sector, retries are attempted
irrespectively of the R bit setting.

The data stored in the buffer, and CRC code and ECC bytes are written to the data
field of the corresponding sector(s).

Upon the completion of the command execution, the shadow block registers
contain the cylinder, head, and sector addresses of the last sector written.

If a disk error occurs during multiple sector write operation, the write operation is
terminated at the sector where the error occurred. Shadow block registers contain
the cylinder, the head, the sector addresses (in the CHS mode) or the logical block
address (in the LBA mode) of the sector where the error occurred.

•

Error reporting conditions

(1) A specified address exceeds the range where write operations are allowed

(after a transfer of dummy data, ST = 51h, ER = 10h).

(2) The range where write operations are allowed will be exceeded by an address

during a write operation (after a transfer of dummy data, ST = 51h, ER = 10h).

(3) A write fault was detected when the write cache was disabled

(ST = 71h, ER = 10h).

(4) While the write cache is enabled, if the status indicating a completed transfer

(STS = 50h) is returned and a data write operation failed because a write fault
was detected during the data write operation, Abort will be returned for all
subsequent ATA commands (ST = 71h, ER = 04h). This state is cleared the
next time that the device is turned on.

(5) A SATA communication error occurred (ST = 51h, ER = 14h).

(6) An error other than the above errors occurred (ST = 51h, ER = 04h).

5-34

C141-E280

«
...
106
107
108
109
110
...
»

Содержание MHZ2080BJ

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHZ2080BJ

Бренд: Park Tool Страницы: 2

Бренд: Backyard Страницы: 63

Бренд: DuraMax Страницы: 81

MediaStore 7200

Бренд: Harmonic Страницы: 2

Mobileraid MR8X

Бренд: Sans Digital Страницы: 81

Бренд: kioxia Страницы: 24

GridLine 930505

Бренд: GARANT Страницы: 116

USO-HA D500 Series

Бренд: STONEFLY Страницы: 58

Бренд: Olympus Страницы: 4

Бренд: Fantom Drives Страницы: 2

Бренд: Fujitsu Страницы: 40

MHW2060BK - Mobile 60 GB Hard Drive

Бренд: Fujitsu Страницы: 12

MHX2300BT - Mobile 300 GB Hard Drive

Бренд: Fujitsu Страницы: 12

MHW2040AT - Mobile 40 GB Hard Drive

Бренд: Fujitsu Страницы: 278

Бренд: Fujitsu Страницы: 296

Бренд: Fujitsu Страницы: 292

MHV2040AT - Hard Drive - 40 GB

Бренд: Fujitsu Страницы: 280

Бренд: Fujitsu Страницы: 278

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды