Fujitsu MHZ2080BJ Скачать руководство пользователя страница 257 | Manualshive

Страница: 257 / 320

background image

5.4 Command Protocol

5.4.5 DMA data-out command protocol

The DMA data-out command is the following command:

•

WRITE DMA (EXT) (FUA EXT)

•

WRITE LOG DMA EXT

The DMA mechanism transfers data of more than one block from the host to the
device. The completion of the command is reported by an interruption.

An outline of this protocol is as follows:

1) The device receives the DMA data-out command with the RegHD FIS.

2) If an error remaining in the device prevents command execution, the device

sends the RegDH FIS with 1 set in the I bit.

3) When the device is ready to receive data, it sends the DMA Active FIS to the

host.

4) The device receives the Data FIS from the host.

5) When all data has been transferred, the device sends the RegDH FIS (with 1

set in the I bit) to complete execution of the command. If any data remains to
be received by the device, this protocol is repeated starting from step 3). (The
maximum data size is 8 KB.)

Device

Host

RegHD

DMA Active

DATA

RegDH

Figure 5.17 DMA data-out command protocol

C141-E280

5-183

«
...
255
256
257
258
259
...
»

Содержание MHZ2080BJ

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHZ2080BJ

Бренд: Megatank Страницы: 12

Бренд: Buffalo Страницы: 77

Бренд: V-TAC Страницы: 28

Бренд: Ravpower Страницы: 15

Бренд: National Instruments Страницы: 20

Бренд: Compaq Страницы: 139

Бренд: KEHUA TECH Страницы: 51

Storage 6180 Array

Бренд: Oracle Страницы: 6

StorageTek SL3000

Бренд: Oracle Страницы: 216

Pillar Axiom 600

Бренд: Oracle Страницы: 229

Tackle Caddy Console

Бренд: RAILBLAZA Страницы: 2

WD VelociRaptor WD1500HLFS

Бренд: Western Digital Страницы: 2

Бренд: Promise Technology Страницы: 25

Бренд: Promise Technology Страницы: 284

DKC-F810I-1PL16

Бренд: Hitachi Страницы: 36

Бренд: Verbatim Страницы: 3

Бренд: Medion Страницы: 112

Бренд: Acomdata Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды