Fujitsu MHZ2080BJ Скачать руководство пользователя страница 156

Страница: 156 / 320

Interface

•

SCT READ DATA (SN = E1h, FR = D5h)

This command reads the data specified with SCT SET COMMAND and number
of sectors specified Sector Count field.

28-bit command

At command issuance (Shadow Block Registers setting)

CM 1

DH x

Key (C2h)

Key (4Fh)

E1h

D5h

At command completion (Shadow Block Registers contents to be read)

ST Status

information

x x

Error information

SCT READ DATA Command issue procedure.

1. Issue the SCT set command of action code 0005h.

2. Issue the SCT READ DATA command and receive the HDA temperature

data from the device.

5-82

C141-E280

Содержание MHZ2080BJ

































































































































































































































































































































Результаты поиска

Содержание MHZ2080BJ

Отзывы:

Fujitsu MHZ2080BJ, Руководство по эксплуатации/техническому обслуживанию, Страница: 156 / 320

Результаты поиска

Содержание MHZ2080BJ

Отзывы: