Fujitsu MHZ2080BJ Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 320

background image

5.2 Logical Interface

(8) Status

field

The contents of this field indicate the status of the device. The contents of this
field are updated at the completion of each command. When the BSY bit is 1,
other bits of this field, are invalid.

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

BSY DRDY DF DSC DRQ

0

0

ERR

- Bit 7:

Busy (BSY) bit

This bit is set whenever the Command filed of the shadow block registers for the host
system is accessed.

Then this bit is cleared when the command is completed. However, even if a command is
being executed, this bit is cleared during the PIO data transfer request.

When BSY bit is 1, the host system should not write the shadow block registers. This bit
is set by the device under following conditions:

(a) After COMRESET or SRST is set in the Device Control Field, the BSY bit is set,

then the BSY bit is cleared, when the COMRESET process is completed.

The BSY bit is set for no longer than 15 seconds after the IDD accepts reset.

- Bit 6:

Device Ready (DRDY) bit

This bit indicates that the device is capable to respond to a command.

The IDD checks its status when it receives a command. If an error is detected (not ready
state), the IDD clears this bit to 0. This is cleared to 0 at power-on and it is cleared until the
rotational speed of the spindle motor reaches the steady speed.

- Bit 5:

Device Write Fault (DF) bit

This bit indicates that a device fault (write fault) condition has been detected.

If a write fault is detected during command execution, this bit is latched and retained until
the device accepts the next command or reset.

- Bit 4:

Device Seek Complete (DSC) bit

This bit indicates that the device heads are positioned over a track.

In the IDD, this bit is always set to 1 after the spin-up control is completed.

- Bit 3:

Data Request (DRQ) bit

This bit indicates that the device is ready to transfer PIO data of word unit or byte unit
between the host system and the device.

- Bit 2:

Always 0

- Bit 1:

Always 0

- Bit 0:

Error (ERR) bit

This bit indicates that an error was detected while the previous command was being
executed. The Error field indicates the additional information of the cause for the error.

C141-E280

5-25

«
...
97
98
99
100
101
...
»

Содержание MHZ2080BJ

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHZ2080BJ

ValueLoader LTO-1

Бренд: Quantum Страницы: 76

Бренд: Keter Страницы: 2

Бренд: Quictent Страницы: 24

Бренд: Fast Mover Страницы: 2

Бренд: NetApp Страницы: 9

Storage 6180 Array

Бренд: Oracle Страницы: 6

StorageTek SL3000

Бренд: Oracle Страницы: 216

Pillar Axiom 600

Бренд: Oracle Страницы: 229

Бренд: DataDirect Networks Страницы: 118

microSDXC UHS-?

Бренд: Toshiba Страницы: 5

IBM Half-high LTO Generation 3

Бренд: Lenovo Страницы: 13

Бренд: Lenovo Страницы: 37

Бренд: Lenovo Страницы: 46

Бренд: Lenovo Страницы: 20

IBM Storwize V7000

Бренд: Lenovo Страницы: 30

Бренд: Lenovo Страницы: 56

Бренд: Lenovo Страницы: 4

Бренд: Lenovo Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды