Fujitsu MHZ2080BJ Скачать руководство пользователя страница 295 | Manualshive

Страница: 295 / 320

background image

7.2 Operation Confirmation

7.2 Operation Confirmation

7.2.1 Operation test

When the host computer is processing data, the disk drive monitors disk drive
operation errors including data, command, and seek errors. The host is notified of
the error that the disk drive detected and the user is notified of its result.

The user may notice intermittent and indefinite failures such as overlong execution
time, abnormal noise, abnormal odor, or failures in particular processes.

The failure reported in the operation test will need further investigation. To
ascertain the cause of the disk drive failure reported, the disk drive can be
replaced. Failures in the operation test are often not caused by the host system.
For example, not having enough power supply reserve, a loose cable connection,
no timing and mechanical reserves, or relationship with other systems.

In normal operation, the disk drive itself or the host determines the processing
(return or halt) following the detected failure state.

To troubleshoot the failure reported in the test at this level, accurately reproduce
the condition that caused the failure. Then, by replacing the disk drive, try to
separate the fault from the other sections of the disk drive host system.

7.2.2 Diagnostic test

The diagnostic test is used to separate a confirmed disk drive failure to a disk drive
subassembly or to check the disk drive performance. A test of this level usually
includes a specific disk drive function or concentrated execution of a group of
functions. The test is usually performed by a factory engineer and not where the
failure was reported. The disk drive is tested using another host computer or test
equipment.

To troubleshoot the disk drive failure in the diagnostic test, the engineer will
reproduce the failure condition. The engineer then isolates the failure to a
subassembly or part of the disk drive.

The procedures used in a test of this level great depend on the test equipment used.
It is beyond the range of this manual.

C141-E280

7-11

«
...
293
294
295
296
297
...
»

Содержание MHZ2080BJ

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHZ2080BJ

Бренд: Qlogic Страницы: 20

Бренд: Backyard Products Страницы: 72

A16F-R2431 Galaxy Raid

Бренд: Rorke Data Страницы: 110

Бренд: U-Line Страницы: 2

Бренд: Acard Страницы: 54

Бренд: Kingston Technology Страницы: 2

Бренд: Homak Страницы: 3

Cold Frame Single

Бренд: Palram Страницы: 11

VPFEM4128GSCBMTL

Бренд: Viking Technology Страницы: 36

Бренд: IBM Страницы: 21

MicroVault USM-L

Бренд: Sony Страницы: 2

MicroVault USM-M1 Series

Бренд: Sony Страницы: 2

MICROVAULT USM-N Series

Бренд: Sony Страницы: 2

MicroVault USM-V Series

Бренд: Sony Страницы: 3

Бренд: Sony Страницы: 92

IPELA NSRE-S200

Бренд: Sony Страницы: 104

Бренд: S&C Страницы: 42

Pro 2-Disk RAID USB and eSATA

Бренд: Verbatim Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды