Fujitsu MHZ2080BJ Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 320

background image

Important Alert Items

Task Alert

message

Page

Maintenance

Device damage

1. Before touching a PCA or the drive, wear a wrist strap

and perform the human body grounding to discharge
static electricity from your body. This will prevent
irreparable damage to the PCA and the head of the drive.

2. Don’t install or remove a PCA or connect or disconnect

a cable or connector plug when the drive is powered.
This will prevent electrical damage to the disk drive.

3. Operating the disk drive with one or more PCA missing

will be unpredictable. Only power the drive with all
boards installed.

4. Avoid any detergent when cleaning the disk drive.

5. Keep all vents open opened and unblocked.

7-2

6. Do not apply excessive force to the cover under any

circumstances. Doing so may cause irreparable damage
to the cover.

Device damage

The DE is completely sealed. Do not open the DE in the
field.

7-3

Data corruption

When asking for repair, save all data stored in the disk drive
beforehand. Fujitsu Limited is not responsible for any loss of
data during service and repair.

7-4

Device damage

The disk enclosure (DE) must never to be opened in the field.
Opening the disk enclosure may cause irreparable damage.

7-14

Damage or Device damage

1. Perform any removal after the system power is

completely disconnected. The cable must not be
disconnected and the screws that attach the drive must
not be removed with the power ON.

2. Do not move the drive and attach or detach the connector

until it comes to a complete stop (about 30 s after the
power is turned OFF).

3. Perform the human body grounding to discharge any

static electricity from your body. (Be sure to wear a
wrist strap)

7-15

vi

C141-E280

«
...
8
9
10
11
12
...
»

Содержание MHZ2080BJ

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHZ2080BJ

Бренд: G-Technology Страницы: 32

Бренд: G-Technology Страницы: 35

301160U - 1TB Ethernet Disk RAID Network Attached...

Бренд: LaCie Страницы: 5

Бренд: LaCie Страницы: 6

Бренд: Xycom Страницы: 27

Бренд: 7-BIT Страницы: 4

Бренд: IBM Страницы: 11

Бренд: Raidon Страницы: 2

PREMIER GAMT41HWJG

Бренд: Gladiator Страницы: 24

220-420LTO - QUICK

Бренд: TANDBERG Страницы: 8

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 4

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 43

Бренд: Samsung Страницы: 60

Бренд: Silvercrest Страницы: 18

Installation andMoBox 18160

Бренд: Silvercrest Страницы: 24

DataBox VI 1000

Бренд: Silvercrest Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды