Fujitsu MHZ2080BJ Скачать руководство пользователя страница 105

Страница: 105 / 320

5.3 Host Commands

(1) RECALIBRATE

to X

1F')

This command performs the calibration. When the device completes the
calibration, the device reports the status to the host system.

This command can be issued in the LBA mode.

•

Error reporting conditions

(1) An error was detected during head positioning (ST = 51h, ER = 02h).

(2) A SATA communication error occurred (ST = 51h, ER = 14h).

At command issuance (Shadow Block Registers setting contents)

0 0 0 1 x x x x

x x x x

At command completion (Shadow Block Registers contents to be read)

ST Status

information

x x x x

Error information

Note:

Also executable in LBA mode

C141-E280

5-31

Содержание MHZ2080BJ

































































































































































































































































































































Результаты поиска

Содержание MHZ2080BJ

Отзывы:

Fujitsu MHZ2080BJ, Руководство по эксплуатации/техническому обслуживанию, Страница: 105 / 320

Результаты поиска

Содержание MHZ2080BJ

Отзывы: