Fujitsu MHZ2080BJ Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 320

background image

5.2 Logical Interface

5.2 Logical Interface

The host system and the device communicate with each other by sending and
receiving serial data.

The host and the device have several dedicated communication layers between
them. These layers have different functions, enabling communication between the
different levels of layers within the host or device and between layers at the same
level that link the host and device.

Figure 5.3 is a conceptual diagram of the communication layers.

Host:
Software control
Buffer Memory
DMA engine(s)

Host located layers

Physical Layer

Link Layer

Transport Layer

Device located layers

Physical Layer

Link Layer

Transport Layer

Device:
Software control
Buffer memory
DMA engine(s)

Application

layer 4

Transport

layer 3

Link

layer 2

Physical

layer 1

Shadow Block Register

Block Register

Figure 5.3 Conceptual diagram of communication layers

C141-E280

5-11

«
...
83
84
85
86
87
...
»

Содержание MHZ2080BJ

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHZ2080BJ

Бренд: Gardiun Страницы: 27

Бренд: Yamaha Страницы: 3

EASY ROLL 170.S/2/PS

Бренд: garofalo Страницы: 12

Paletto 00108043

Бренд: Hama Страницы: 4

Бренд: Suncast Страницы: 28

LITTLE DISK USB 2.0

Бренд: LaCie Страницы: 23

Бренд: Air innovations Страницы: 30

Бренд: ABB Страницы: 2

Бренд: ABSCO SHEDS Страницы: 21

Бренд: Seagate Страницы: 2

Бренд: 3Ware Страницы: 50

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 10

Бренд: Sony Страницы: 32

Бренд: Sony Страницы: 34

Бренд: Sony Страницы: 40

Бренд: Sun Microsystems Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды