Fujitsu MHZ2080BJ Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 320

background image

5.3 Host Commands

Table 5.9 Features Field values (subcommands) and functions (3/3)

Features Field

Function

X 'D9'

SMART DISABLE OPERATIONS:
This subcommand disables SMART. The setting is maintained even when
the device is turned off and then on.
When the device receives this subcommand, it disables SMART, then
transfers the RegDH.

X 'DA'

SMART RETURN STATUS:
When the device receives this subcommand, it saves the current device attribute
values. Then the device compares the device attribute values with guarantee
failure threshold values. If there is an attribute value exceeding the threshold,
F4h and 2Ch are loaded into the Cylinder Low and Cylinder High field. If there
are no attribute values exceeding the thresholds, 4Fh and C2h are loaded into
the Cylinder Low and Cylinder High field. After the settings for the Cylinder
Low and Cylinder High field have been determined, the device transfers the
RegDH.

X 'DB'

SMART ENABLE/DISABLE AUTO OFF-LINE:
This sets automatic off-line data collection in the enabled (when the Sector
Count field specification

≠

00h) or disabled (when the Sector Count field

specification = 00) state. This setting is preserved whether the drive's power
is switched on or off.
If 24 hours have passed since the power was switched on, or since the last
time that off-line data were collected, off-line data collection is performed
without relation to any command from the host computer.

The host must regularly issue the SMART READ DATA subcommand (Features
field = D0h), SMART SAVE ATTRIBUTE VALUES subcommand (Features
field = D3h), or SMART RETURN STATUS subcommand (Features field = DAh)
to save the device attribute value data on a medium.

Alternative, the device must issue the SMART ENABLE-DISABLE ATTRIBUTE
AUTOSAVE subcommand (Features field = D2h) to use a feature which regularly
saves the device attribute value data to a medium.

In this drive, this function is enabled at the shipment from the factory.

The host can predict failures in the device by periodically issuing the SMART
RETURN STATUS subcommand (Features field = DAh) to reference the Cylinder
Low and Cylinder High field.

If an attribute value is below the guarantee failure threshold value, the device is
about to fail or the device is nearing the end of its life. In this case, the host
recommends that the user quickly back up the data.

C141-E280

5-57

«
...
129
130
131
132
133
...
»

Содержание MHZ2080BJ

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHZ2080BJ

Бренд: Backyard Products Страницы: 72

EASY ROLL 170.S/2/PS

Бренд: garofalo Страницы: 12

BLACKOUT WINDOW STORAGE SYSTEM

Бренд: REBEL OFF ROAD Страницы: 9

Бренд: U-Line Страницы: 18

Barracuda 7200.7 ST3120228AS

Бренд: Seagate Страницы: 2

Бренд: Sans Digital Страницы: 2

Бренд: Dell EMC Страницы: 70

Бренд: G&T SALES Страницы: 2

Бренд: Quantum Страницы: 3

Бренд: Craftsman Страницы: 6

Tool Storage Roll-Away

Бренд: Craftsman Страницы: 4

HEAVY DUTY TOOL CHESTS

Бренд: Craftsman Страницы: 8

Бренд: Craftsman Страницы: 16

microSDXC UHS-?

Бренд: Toshiba Страницы: 5

Бренд: NEC Страницы: 4

Бренд: NEC Страницы: 8

Бренд: NEC Страницы: 12

Бренд: NEC Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды